Bedienungsanleitung Silvercrest SDWH 180 A1 - IAN 285970 (Seite 25 von 52) (Deutsch, Englisch, Holländisch)

668039

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

26 GB/IE

Cleaning and Care / Disposal / Warranty / Service centreChanging the batteries / Troubleshooting

4. Note: If the scales do not appear to work,

check that the battery has been inserted

correctly and reinsert it if necessary.

Hand-held unit

1. Remove the battery cover

from the battery

compartment in the direction of the arrow.

2. Remove the exhausted battery and dispose of

it as described in the section about “Disposal”.

3. Place the new battery in the battery compart-

ment. Please note the polarity. The “+” symbol

must be visible on the top of the battery. Press

the battery gently downwards and push the

battery cover

back on to the battery com-

partment.

Note: When you insert the battery, make sure

that the contacts do not get bent.

4. Note: If the LC display

does not appear to

work, check that the batteries have been in-

serted correctly and reinsert them if necessary.

Troubleshooting

= Error

= Cause

= Solution

The wrong weight is being displayed.

The scales have an incorrect zero point.

Step brieﬂy oﬀ the scales and wait until the

scales switch oﬀ. Repeat the measurement

process.

The scales are not on a level, stable surface.

Place the scales on a level, stable surface.

You are not standing still.

Stand as still as possible.

The LC display

shows „Err“.

The maximum load capacity of

180 kg / 396 lb / 28 st has been exceeded.

Only load the scales up to

180 kg / 396 lb / 28 st.

The LC display

shows „ErrL“.

The proportion of fat is outside of the

measurable range.

Measurement of body fat is not possible,

because the proportion of body fat is below

the measurable range.

The LC display

shows „Errh.“

The proportion of fat is outside of the measura-

ble range.

Measurement of body fat is not possible, be-

cause the proportion of body fat is above the

measurable range.

The LC display

shows „- - - -“.

Body fat measurement not possible.

Please repeat the measurement process bare-

foot or lightly moisten the soles of your feet.

The hand-held unit

has not received data

from the infrared sensor

Repeat the measurement process. After select-

ing the user, step onto the scales barefoot

within 15 seconds to start the body fat meas-

urement. Ensure that there are no objects lo-

cated between the infrared sensor

and

infrared receiver

and that these are not

covered.

The LC display

shows „hLo“.

The battery of the hand-held unit

is spent.

Change the battery in the hand-held unit

The LC display

shows „bLo“.

The battery in the scales is spent.

Change the battery in the scales.

The LC display

only shows the time.

A weight measurement is not possible.

Check to see whether there are obstacles be-

tween the infrared transmitter

and infrared

receiver

which may aﬀect transmission

(i.e. furniture, ﬁngers, stomach, etc.). Repeat

the measurement process and hold the infrared

receiver

directly over the infrared transmit-

ter

while doing so.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SDWH 180 A1 - IAN 285970 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info