Bedienungsanleitung Silvercrest SEK 2000 B2 - IAN 365183 (Seite 13 von 118) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

793242

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

GB/IE/NI/CY/MT 13

5. Starting-up

Please find a suitable location for the device before

starting it up.

For safe and trouble-free running of the device,

choose an installation location which meets the

following requirements:

– The floor should be firm, flat and horizontal.

– The device should be set up at least one metre

away from furniture, curtains and other easily

flammable objects.

– Do not place the device in a hot, wet or very hu-

mid environment.

– A grounded socket protected by a residual-current

device with overload protection should be availa-

ble in the vicinity of the device.

– The power socket should be easily accessible so

that the mains connection cable can be easily di-

sconnected, if necessary.

– Extension cords are prohibited.

Plug the device cable into the grounded power

socket.

IMPORTANT! The cable must remain on the rear-

side of the device and must not come into contact

with any hot elements.

5.1 Device operation

The device is operated via the operation panel

2 and the thermostat 3 on the right-hand side

(Fig. 5).

The first switch with the [ ] symbol switches

the flame effect on and off. The flame effect can

be used with or without the heating function. If

the switch is set to the [ O ] symbol, the flame

effect is switched off. If you press the switch to

the left [‒], you will activate the device.

For a low amount of heating, switch the first hea-

ting level with the [ I ] symbol to the [‒] symbol

to turn it on and to the [ O ] symbol to turn it

off. The heating function can be used with or

without the flame effect.

For full heating power, switch on both heating

levels [ I ] and [ II ] using the on/off switches.

Heating level [ II ] only functions if the switch for

heating level [ I ] is also set to the [‒] symbol.

The temperature of the two heating stages can

be controlled using the thermostat 3 by setting

it between the [‒] and [+] settings. Turning the

thermostat 3 clockwise until you hear an audi-

ble click will switch on the device. [‒] represents

the lowest temperature (left) and [+] (right) the

highest temperature.

PLEASE NOTE! Thanks to automatic operation,

the hot-air control (thermostat) maintains the pre-

programmed temperature at a constant level.

First, turn the thermostat 3 to the right in the

direction of the maximum value. Leave the

switch in this position until the air in the room

has reached your desired temperature.

PLEASE NOTE! When you use the device for the

first time, a slight odour may occur.

5.2 Overheat protection

For your safety, this device features overheating pro-

tection. If the temperature inside the device becomes

too high, it will switch off automatically. In this case,

proceed as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SEK 2000 B2 - IAN 365183 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info