590842
9
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
6
SEMD 12 A1
GB
IE
Making ice cream
CAUTION! MATERIAL DAMAGE!
Start the appliance fi rst and then add ingre-
dients. Otherwise the ice mixture will freeze
onto the sides of the beaker 8 and block the
ice scrapers 7. This will cause the motor to
overheat!
CAUTION! MATERIAL DAMAGE!
Do not stop the appliance during processing!
Otherwise the ice mixture will freeze onto
the sides of the beaker 8 and block the ice
scrapers 7 when the machine is restarted.
This will cause the motor to overheat!
1) Remove the beakers 8 from the freezer and
put the appliance together as described in the
section "Assembly".
2) Switch the appliance on by moving the On/
Off switch 1 to the position I. The two ice
scrapers 7 start turning.
3) Now fi ll the prepared ice mixture into the beak-
ers 8 through the fi lling openings 4. Ideally,
use a bowl with a spout. Never add more than
300 ml per beaker 8. During processing the
mixture increases in volume!
NOTE
You can also fi ll only one beaker 8 with
ingredients. However, always use the appli-
ance with both beakers.
NOTE
The ice scrapers 7 may occasionally change
their direction of rotation. This happens when
the mixture becomes too stiff . This is normal
and not an appliance defect.
4) Allow the appliance to continue running until
you are satisfi ed with the consistency of the
mixture. After a maximum of 20 to 30 minutes,
the ice cream is ready.
5) Switch the appliance off at the On/Off switch 1
and pull the mains power plug out of the socket.
6) Turn the rotary switch 9 to
to remove the
lid 5 with the motor unit 2.
7) Pull the ice scrapers 7 out of the ice cream.
If the ice cream sticks to them, scrape it off with
a plastic spoon or similar.
8) Lift the beakers 8 out of the appliance and
remove the ice cream. Use only plastic or
wooden implements to do this.
CAUTION! MATERIAL DAMAGE!
Do not use metal utensils to remove the ice
cream from the beakers 8.
NOTE
If you would like to replace the lid 5 on
the beakers, you must fi rst detach the motor
unit 2 from the lid 5. Then proceed as de-
scribed in the section "Assembly". Otherwise,
it is possible that the drive shafts 3 do not
slide correctly into the drive shaft socket 6.
IB_111458_SEMD12A1_FI_BE_NL.indb 6 05.03.15 10:27
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Silvercrest SEMD 12A1 - DUO ICE CREAM MAKER - IAN 111458 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info