Bedienungsanleitung Silvercrest SFB 10.1 B2 - IAN 71477 (Seite 14 von 109) (Englisch)

621607

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

- 12 -

number 5 the display skips to the letter "J". The rst brand

is "JEC"*. If, for example, you own a "Kenwood"* brand

device, continue leang with the 4 button t until this

brand name appears. (* All brand names used here are

trademarks of the corresponding manufacturer.)

7. The majority of manufacturers use several dierent codes

for the remote control. You must now ascertain which of

the available codes is best suited to your device. On the

right underneath the brand name the relevent code will

be shown in the LCD display q.

8. To test the code, point the remote control at the actual

device and press the buttons that correspond to the func-

tions of this device (except

34t, OK l, EXIT y,

the device buttons e or the numeric buttons o).

9. If most of the buttons function press the OK button l to

save the setting. In the LCD display q "OK" appears.

Subsequently the menu will close automatically.

10. If, however, none or only a few of the buttons function

select with the

 or  button t the next code and test

again as described in step 8.

11.

With the EXIT button y you move back one level in the

menu.

Repeat these operational steps for all devices that you would

like to control with the remote control.

Programming by manual code input

In this mode the remote control can be programmed by direct

input of a code number. You can obtain the necessary code

number from the enclosed manufacturers directory with device

code list. In the event that the new code is invalid the last valid

programmed code will be restored.

1. Press the device button e for the device that you want to

programme the remote control.

2.

Hold down the S button r for a little longer than 3 sec-

onds. “LANGUAGE SETUP” appears in the LCD display

q. With the  or  button t select “CODE SETUP” and

conﬁrm with the OK button l.

3. "ENTER CODE" now appears in the LCD display q.

To

access this function press the OK button l.

4. In the LCD display q appears the presently used code for

the selected device. Now the rst digit of the code blinks

and waits for your code input. Enter the new four digit

code via the number buttons o. After entering the fourth

digit the whole code ashes. You can now test if the URC

can control the device you want with this code. Press

those keys that correspond to the functions of the device,

with a TV set for example, PROG +/–. If the device re-

acts as required, conrm the code input with the OK but-

ton l. If it does not, enter the next possible code from the

list and try again.

5. If the entered CODE is valid the code will be saved. In

the LCD display q "OK" appears briey. Subsequently

BDA_SFB 10.1 B2 - DT-71477_gb.indd 12 23.11.2011 16:24:24

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SFB 10.1 B2 - IAN 71477 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SFB 10.1 B2 - IAN 71477

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info