628972
19
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
SilverCrest SFR 2.4 B1
English 17
Powering the Transmitter Cradle Off
You may power the transmitter cradle off whenever it is not needed. When powered off, it will not
transmit any RF signals but the headphones battery will still be charged.
1. Slide the On/Off switch (12) on the transmitter cradle to the “OFF” position. The send
indicator (17) on the transmitter goes out.
You may optionally power the transmitter cradle using conventional batteries. For more
information see page 21 – “Powering the Transmitter Cradle Using Batteries”.
Synchronising the Headphones and Transmitter Cradle
After powering the headphones and the transmitter cradle on, both devices should synchronise
automatically. This process may take a while (sometimes more than 1 minute), but normally you
just have to be patient.
Under unfavourable circumstances, however, the audio signal may be subject to interference. This
may happen if you are using a baby phone or a wireless keyboard and mouse set nearby. In this
case you can synchronise the devices manually to locate an interference-free channel.
1. Power the transmitter cradle on by sliding the On/Off switch (12) on the transmitter cradle to
the “ON” position.
2. Power on the connected audio source and start playback. The send indicator (17) on the
transmitter cradle should light up green.
3. Slide the mode selection switch (6) of your headphones to the “WL” position.
4. Power the wireless headphones on by pressing the On/Off button (9) once.
5. Press and hold the synchronisation button (3) of the headphones and the synchronisation
button (13) of the transmitter cradle for at least 1 second.
The RF reception indicator on the headphones (2) and the send indicator on the transmitter
cradle (17) start blinking. As soon as both devices have synchronised, both indicators will
light up green.
6. If necessary, repeat step 5 if you are not satisfied with the reception quality or you still have
interference from other devices.
Synchronising the transmitter cradle and the headphones can take a while. If
there are many wireless devices nearby using the 2.4 GHz RF technology, the
transmitter cradle and headphones first have to find a free communications
frequency. Any frequencies that are already occupied by other devices will
not be used. This is also known as “WLAN Skipping and Hopping”.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

silvercrest-sfr-2.4-b1---ian-75760

Suche zurücksetzen

  • Kopfhörer Schaltet wehrend des Betriebes ab und muss dann wieder eingeschaltet werden ca,3min Eingereicht am 21-1-2019 12:18

    Antworten Frage melden
  • Kann der Rasierer von Silvercrest SFR 37 b1 überhitzen, wenn man vergisst ihn vom Netzanschluss zu nehmen? Eingereicht am 28-11-2017 21:21

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Silvercrest SFR 2.4 B1 - IAN 75760 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info