Bedienungsanleitung Silvercrest SFW 100 B2 IAN 90994 (Seite 9 von 45) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

740075

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

9 GB

Important safety instructions / Safety system / Preparing the product for use

or damage. If you ﬁnd such signs of damage,

if the cables are damaged or if the foot

warmer has not been used properly, it must be

returned to the manufacturer or to the service

department before it is used again. There is a

danger of electric shock and injury.

Repairs must only be carried out by specially

trained personnel or at a repair shop author-

ised by the manufacturer, since special tools

are necessary. Unsatisfactory repairs can lead

to considerable danger for the user.

Only have the foot warmer re-

paired by qualiﬁed specialist personnel using

OEM spare parts. This will ensure your foot

warmer remains safe to use.

If the mains power cable of the

foot warmer is damaged, it has to be replaced

by the manufacturer or its service department

or a similarly qualiﬁed person in order to avoid

hazards.

Safety system

Note: This foot warmer is equipped with a safety

system. The electronic sensor technology prevents

the entire surface of the foot warmer from overheat-

ing by automatically switching oﬀ in the event of a

fault. If the safety system switches the foot warmer

oﬀ automatically due to a fault, then the function

display

on the control unit

is no longer illu-

minated, even if the heating pad is switched on.

Please note that, for safety reasons, the foot

warmer must not be used after a fault and must

be returned to the service address indicated.

Preparing the product for use

Note: When the foot warmer is used for the ﬁrst

time, you may notice a smell of plastic; however,

this will disappear after a short time.

Switching on / oﬀ / Selecting

the temperature

Insert the mains plug into the mains socket.

Switching on:

Set Level 1, 2, 3, 4, 5 or 6 on the control

unit

to switch the foot warmer on.

Note: The function display

illuminates

after the foot warmer is switched on.

Note: This foot warmer features rapid heating,

which allows it to heat up within the ﬁrst 15

minutes of operation.

Switching off:

Set Level 0 on the control unit

to switch the

foot warmer oﬀ.

Note: the function display

ceases to illuminate.

Selecting the temperature:

Just before using the heating pad, set it to the

highest temperature setting (setting 6). This will

cause the heating pad to warm up quickly.

If you are going to use the foot warmer for a

number of hours, set it to the lowest tempera-

ture setting (setting 1).

The foot warmer can of course be used at any

time if it is switched oﬀ. Its teddy plush lining

will warm your feet even if an electric socket is

nowhere near.

Temperature levels

Set the required temperature level on the

control

Level 0: Oﬀ

Level 1: minimum heat

Level 2 - 5: Customised heat

Level 6: maximum heat

90994_silv_Fußwaermer_content_LB3 (GB-DK-BE).indd 9 29.05.13 09:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SFW 100 B2 IAN 90994 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info