Bedienungsanleitung Silvercrest SHBS 700 A1 - IAN 354063 (Seite 14 von 67) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

777999

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

14 GB/IE/NI

Place the thinning attachment 12 onto the pro-

duct as described in the chapter “Changing

the attachments.“

Note: The thinning attachment 12 prevents

every hair from being cut.

Trimming beards

Note that the desired trim length can only be

achieved if the product is held perpendicularly

to the skin‘s surface.

Comb the beard using the supplied comb 17

in its direction of growth.

Shorten the beard downwards from the ear to

the chin, one side after the other.

Use the cutting unit 1 without the comb attach-

ment 11 to trim the beard very short or to trim

a moustache or hairline.

Graduate the desired trim length by rotating

the lower part of the product 5 according to

length position indicator 4. The trim length

may be set to 5 diﬀerent levels (0.8 mm/

1.1 mm/1.4 mm/1.7 mm/2.0 mm).

To trim a moustache, ﬁrstly comb it straight

downwards. Begin in the centre above the

mouth, then one side and then the other.

Cleaning and care

CAUTION! DANGER TO LIFE BY ELECTRIC

SHOCK! Pull the plug-in mains adapter 7 out

of the mains socket before cleaning the product.

Never touch the plug-in mains adapter 7 with

moist or wet hands, especially when you plug

it into the socket or pull it out of the socket.

Always keep the plug-in mains adapter 7 and

supply cord dry.

CAUTION! RISK OF PROPERTY DA

MAGE!

Do not submerge the product in water or any

other liquid to clean it as the product is not

waterproof. This could damage the live parts

(rechargeable batteries).

Do not use any corrosive or abrasive cleaning

agents.

Clean the housing and the charging base 6

using a damp cloth and a mild detergent.

Switch the product oﬀ by pressing the ON/

OFF button 3 b once or twice, until the indicator

light 3 a goes oﬀ.

Disconnect the supply cord from the product

and remove the plug-in mains adapter 7 from

the mains socket.

Remove the comb attachment 11 , the thinning

attachment 12 or the cutting unit 1 from the

product (see Fig. G + H).

Wash the comb attachment 11 , the thinning

attachment 12 or the cutting unit 1 with run-

ning water if necessary.

Dry the comb attachment 11 , the thinning

attachment 12 or the cutting unit 1.

Remove the cutting unit 1 (see Fig. H).

Remove any remaining bits of hair from the

cutting unit 1 using the cleaning brush 13

provided (see Fig. I).

Apply one or two drops of blade oil 14

between the blades and the moving parts

(see Fig. J).

Adjust the length position indicator 4 to

2.0 mm after you have ﬁnished cleaning the

product, before once more attaching the

cutting unit 1 to the product (see Fig. K).

Note: Clean the cutting unit 1, comb attach-

ment 11 and thinning attachment 12 after

every use.

Storage

Place the product in the charging base 6 if

you wish to store it. Alternatively, you can also

store it in the travel case 16 provided.

Troubleshooting

Error Cause Solution

The product

does not

work.

The battery

may not be

charged.

Recharge the

product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SHBS 700 A1 - IAN 354063 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info