Bedienungsanleitung Silvercrest SKM 550 B1 - IAN 274393 (Seite 26 von 272) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

649214

Zoom out

Zoom in

Vorherige Seite

1/272

Nächste Seite

■ 22

│

SKM 550 B1

After you have ﬁnished

using your appliance

1) Switch the appliance oﬀ using the rotary

switch ..

2) Set the rotary switch . to P and hold it in

this position until the drive unit 6 comes to a

standstill (Image B).

3) Remove the lid.

4) Press down the release button ! and move

the pivot arm 0 into operating position 4.

5) Remove the attachment you have been using

from the drive unit 6.

6) Remove the mixing bowl .

7) Clean the appliance (see section “Cleaning

and care”).

Working with

the continuous shredder

WARNING! RISK OF INJURY!

► To avoid personal injury and damage to the

appliance, never insert or place your hands

or any foreign objects into the feed tube.

► Always use the pusher and no other implement

or body part to push ingredients into the

appliance. Danger of injury due to rotating

parts!

► Switch from one accessory to another only

when the drive unit 6 is at a complete stand-

still! After being switched oﬀ, the drive unit 6

will continue to run for a short time.

► In cases of malfunction, switch the appliance

oﬀ and remove the plug from the wall socket.

This will prevent the appliance from becoming

switched on again unintentionally.

NOTE

► The appliance may only be used when the

drive hubs not being utilised are ﬁtted with

their protective covers.

► Make sure that neither the kneading hooks ,

the whisk , or the beater  are attached

to the pivot arm 0.

Proceed as follows to prepare the appliance for

operation using the continuous shredder :

1) Press down the release button ! and move

the pivot arm 0 into operating position 4

(see the section “Operating positions”).

2) Set the mixing bowl  into place. The base

of the mixing bowl  must click into the re-

cesses 1 on the appliance.

3) Press down the release button ! and move

the pivot arm 0 into operating position 2.

4) Remove the protective cover from the drive

for the continuous shredder (Image C).

5) Insert the continuous shredder  into the

hub socket (aligning the marking “

” on the

continuous shredder  with the marking “ ”

on the pivoting arm 0).

Turn it in an anti-clockwise direction until the

continuous shredder  clicks ﬁrmly in place

(and the marking “ ” on the continuous shred-

der  is aligned with the marking “ ” on

the pivoting arm 0).

6) Set the drive shaft  into place.

7) Depending on the task you want to perform,

place the cutting -, shredding  or grating

disc  onto the drive shaft  of the continous

shredder .

8) Place the lid with the pusher 3 onto the con-

tinuous shredder  (so that the marking “

”

on the lid 3 is lined up with the marking “ ”

on the continuous shredder ) and lock the

lid in (marking “ ” on the lid 3 is lined

up with the marking “ ” on the continuous

shredder ).

9) Turn the rotary switch . to the required setting.

NOTE

► Do not press too much food into the continuous

shredder . Take note of the table in the sec-

tion "Recommended ﬁlling levels".

10) Add the ingredients through the opening in the

lid with the help of the pusher.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SKM 550 B1 - IAN 274393 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info