Bedienungsanleitung Silvercrest SKM 550 B1 - IAN 43111 (Seite 39 von 121) (Deutsch, Englisch, Holländisch)

679455

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

SKM 550 B1

Working with the kneading

hook, beater and whisk

WARNING! RISK OF INJURY!

► Under no circumstances should you place

your hands or ﬁ ngers in the mixing bowl 6

during operation! Danger of injury due to

rotating parts!

► Switch from one accessory to another only

when the drive unit z is at a complete

standstill! After being switched oﬀ , the drive

unit z will continue to run for a short time.

► In cases of malfunction, switch the appliance

oﬀ and remove the plug from the wall socket.

This will prevent the appliance from becoming

switched on again unintentionally.

NOTE

► The appliance may only be used when the

drive hubs not being used are ﬁ tted with their

protective covers.

Proceed as follows to prepare the appliance for

operation using the kneading hook 1, beater 3

and whisk 2:

1) Press down the release button e and move

the pivoting arm t into operating position 4

(see the section “Operating positions”) (Image

A).

2) Set the mixing bowl 6 into place. Check that the

base of the mixing bowl 6 is inserted fully into

the recesses u provided for it on the blender.

3) Press down the release button e and move

the pivoting arm t into operating position 1

(Image A).

4) Set the rotary switch r to P and hold it in this

position until the drive unit z settles in its “Park”

position (Image B). If the drive unit z doesn’t

move, it is already in its park position (Fig. 2).

5) Press down the release button e and move

the pivoting arm t into operating position 4

(Image A).

6) If you want to use the kneading hook 1, insert

the dough deﬂ ector into the drive unit z

(Image D). Ensure that the hole through which

the kneading hook is inserted is lying over the

mounting hole on the drive unit z.

7) Depending on the task to be performed, insert

the kneading hook 1, beater 3 or whisk 2 so

that they ﬁ rmly click ﬁ rmly into the drive unit z.

8) Add the ingredients you wish to process into

the mixing bowl 6.

NOTE

►

While kneading and/or mixing, please note

that the dough in the mixing bowl 6 will in-

crease in volume or will be pressed upwards

by the tool. Take note of the table in the sec-

tion "Recommended ﬁ lling quantities".

9) Press down the release button e and move

the pivoting arm t down into operating

position 1 (Image A).

10) Slide the lid onto the mixing bowl 6 so that the

catches on the pivoting arm t click into place.

11) Turn the rotary switch r to the required setting.

Reﬁ lling with ingredients

■ Add the ingredients through the hole in the lid

during operation.

Or:

1) Switch the appliance oﬀ using the rotary

switch r.

2) Set the rotary switch r to P and hold it in

this position until the drive unit z comes to a

standstill (Image B).

3) Remove the lid.

4) Press down the release button e and move

the pivoting arm t into operating position 5.

5) Add the ingredients.

IB_43111_SKM550B1_LB1.indb 35 19.05.14 16:03

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SKM 550 B1 - IAN 43111 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info