Bedienungsanleitung Silvercrest SNMD 33 A1 - IAN 114195 (Seite 91 von 94) (Deutsch, Englisch, Holländisch, Französisch)

614543

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Problem Cause Correction

Upper thread

breaks

Lower thread

breaks

Skipped stitches

Needle breaks

Loose stitches

Seams gather

or pucker

Uneven stitches,

uneven feed

The machine is

noisy

Thread wraps

around thread

spool pin

The machine

jams

1.The machine is not threaded correctly.

2.The thread tension is too tight.

3.The thread is too thick for the needle.

4.The needle is not inserted correctly.

5.The thread has become wound

around the bobbin winder spindle (14).

6.The needle is damaged.

1.The bobbin case is not inserted

correctly.

2.The bobbin case is threaded wrongly.

1.The needle is not inserted correctly.

2.The needle is damaged.

3.The wrong size needle has been

used.

4.The wrong presser foot is installed.

1.The needle is damaged.

2.The needle is not correctly inserted.

3.Fabric too thick/ needle size wrong.

4.The wrong presser foot is attached.

1.The machine is not correctly threaded.

2.The bobbin case is not correctly

threaded.

3.Needle/ fabric/ thread combination is

wrong.

4.Thread tension wrong.

1.The needle is too thick for the fabric.

2.The stitch length is wrongly adjusted.

1.The thread is too weak.

2.The bobbin case is wrongly threaded

3.Fabric has been pulled when sewing.

1.The machine must be lubricated.

2.Fluff or oil have collected on the hook

or needle bar.

3.Poor quality oil has been used.

4.The needle is damaged.

The second thread spool pin was not

used.

Thread is caught in the hook.

1.Rethread the machine.

2. Reduce the thread tension (3). (lower number)

3.Use a larger needle.

4.Remove and reinsert the needle. (flat side

towards the back)

5.Remove the bobbin (g) and unwind the

thread.

6.Replace the needle.

1.Remove and reinsert the bobbin case and

pull on the thread. The thread should pull

easily.

2.Check both bobbin (g) and bobbin case.

1.Remove and reinsert needle. (flat side

towards the back)

2.Replace the needle.

3.Choose a needle size to suit the thread and

fabric.

4.Use the correct presser foot.

1.Replace the needle.

2.Insert the needle correctly (flat side towards

the back)

3.Choose a needle size to suit the thread and

fabric.

4.Use the correct presser foot.

1.Thread the machine correctly.

2.Thread the bobbin case as illustrated.

3.The needle size must suit the fabric and

thread.

4.Correct the thread tension.

1.Use a finer needle.

2.Check the thread tension.

1.Use stronger thread.

2. Rethread the bobbin case and insert correctly.

3.Do not pull on the fabric. It must be

automatically moved by the machine.

1.Lubricate as described.

2.Clean the hook and feed dog as described.

3.Only use good quality sewing machine oil.

4.Replace the needle.

Proceed according to the directions on page

77, "Setting up the thread spool pins".

Remove the upper thread and bobbin case,

turn the handwheel (21) backwards and

forwards by hand and remove the thread

remains. Lubricate as described.

GB / IE 91

Trouble shooting guide

Maintenance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SNMD 33 A1 - IAN 114195 Seite 91

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info