Bedienungsanleitung Silvercrest SPU 900 A2 - IAN 90514 (Seite 70 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

651496

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

- 67 -

The higher the brightness, the greater is the

power consumption of the device.

When you brieﬂy press the MODE/LOCK

button e during radio operation, you can

toggle between frequency and time display.

Projection

The time can be projected from the appliance

onto a wall or the ceiling. This function is in-

tended for reading the time in darkness.

During the day in well lit rooms you will

hardly be able to use the projection facility.

When projection is switched on, the projection

symbol glows in the display g.

1. For this, ﬁrst fold the projector t out.

2. Switch the function on with the PROJEC-

TION button u.

3. Direct the projector t onto the desired

surface area. Before you can turn the pro-

jector t - if so desired - to the side, you

must carefully pull its base up from the

device housing.

4. Using the focus regulator 1( sharpen the

image.

5. The time will now be projected onto the

desired surface area for the pre-adjusted

timespan (see section "Adjusting the Pro-

jection duration").

6. To display the projection back to front,

press and hold the button PROJECTION u

for one second. Pressing and holding it once

again lets the projection appear as normal.

7. Should you wish to switch this function oﬀ

prematurely, press the PROJECTION but-

ton u and fold the Projector t in.

Button lock

Press and hold the MODE/LOCK button e

until the key symbol is indicated in the dis-

play g. The normal key functions are now

blocked. The buttons retain, however, the

function “Alarm stop”. In addition, the button

SNOOZE/DIMMER y as the snooze button

and for setting the display brightness. To dis-

able the button lock function, press and hold

the MODE/LOCK button e once again until

the key symbol extinguishes.

Cleaning

Warning!

Always remove the mains power plug

before cleaning the appliance! Moisture

penetrating into the appliance creates

the risk of electric shock! Additionally,

the appliance could become irreparably

damaged!

Clean the housing of the radio alarm only

with a slightly moist cloth and a mild deter-

gent. Ensure that moisture cannot permeate

into the appliance during cleaning!

Troubleshooting

The appliance doesn't work.

> Is the plug of the power cable 2! inserted

ﬁrmly into the power socket?

> Has the circuit breaker tripped?

> Is there a power cut?

Poor VHF reception.

> Change the alignment of the wire aerial

2). If necessary, ﬁrmly position it with

adhesive tape.

Loss of all programming after a power

cut.

> Batteries were not inserted to retain the

memory.

> The batteries inserted for memory reten-

tion are exhausted. Replace them.

The projected time is diﬃcult to read.

> Using the focus regulator 1( sharpen the

image.

Notice regarding conformity

In regard to compliance with essential re-

quirements and other relevant provisions,

this device complies with the European

Electromagnetic Compatibility Directive

2004/108/EC, the Low Voltage Directive

2006/95/EC and the Ecodesign Directive

2009/125/EC (Ordinance 1275/2008

BDA_SPU 900 A2 - IAN-90514_1_en.indd 67 22.07.2013 13:42:57

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SPU 900 A2 - IAN 90514 Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info