Bedienungsanleitung Silvercrest STK 650 A1 IAN 66500 (Seite 30 von 41) (Englisch, Portugiesisch, Spanisch)

738693

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

- 28 -

3. Pour the desired quantity of water into the glass

pot 3. NEVER fill it with more water than to the

MAX marking, and never with less than to the

MIN marking.

Important!:

To avoid scalds/burns and electric shocks, ensure

that water does not overflow from the glass pot 3.

4. Take hold of the brew system and pull the water

riser pipe w with the sieve e upwards.

5. Place the necessary amount of tea or number of

teabags in the brew chamber q.

Important:

Ensure that no labels or teabag strings remain in the

appliance.

6. Replace the brew system in the glass pot 3.

Ensure that the water riser pipe w sits firmly in

the recess on the bottom of the glass pot 3. The

brew chamber q must be positioned with the

flattened side towards the handle 2.

7. Close the appliance lid 1.

8. Replace the glass pot 3 back on to the

base 5.

9. Insert the plug into a wall power socket and place

the On/Off switch 8 at the position “I”. The

control lamp 4 and the On/Off switch 8 light

up.

The water is now boiled and forced upwards

through the water riser pipe w to flow through the

brew chamber q and then back into the glass pot 3.

After the water has boiled, the appliance automati-

cally switches itself into the keep-warm function. The

control lamp 4 goes out, only the On/Off switch 8

continues to glow. As soon as the water cools, the

Tea Automat warms the water back up. The control

lamp 4 lights up again during this rewarming pro-

cess.

Important:

As the water is fed back through the brewing system

during the rewarming, after the first brewing process

you should remove the brew system from the glass

pot 3.

Risk of personal injury!

The brew system is very hot! There is a risk of being

burnt! Use oven gloves when you take hold of the

brew system.

Note:

The longer the brew is kept warm, the greater is

the amount of fluid evaporated, and thus the brew

becomes stronger.

We therefore recommend that the tea be drunk as

soon as possible after brewing.

You can interrupt the brew process at any time:

For this, place the On/Off switch 8 back into the

position “0”. The brew process is finished.

If you remove the glass pot 3 from the base 5,

the brew process is interrupted.

Important!:

Always first let the glass pot 3 cool down before

you pour in fresh cold water for another brewing

process! Otherwise, tension may be created in the

glass pot 3 and it could shatter.

Overheating protection

In the event of overheating, thermal protection switches

the heating element off inside the appliance. The

On/Off switch 8 remains lit, the appliance however

does not continue to heat up.

The thermal protection is activated if no or not enough

water is in the glass pot 3 and the appliance is

switched on anyway.

IB_66500_STK650A1_LB5 31.05.2011 10:14 Uhr Seite 28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest STK 650 A1 IAN 66500 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest STK 650 A1 IAN 66500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info