Bedienungsanleitung Silvercrest Z30936 IAN 75129 (Seite 19 von 25) (Englisch, Italienisch, Portugiesisch, Spanisch)

739747

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

19 GB/MT

scales and the battery is too weak, the LC display

shows “Lo” (see Fig. C) and the scales switch

oﬀ automatically.

If you see this message, replace the exhausted

battery with a new battery of the same type.

When you insert the battery, make sure that the

contacts do not get bent.

Setting the units of weight

Note: The standard unit of weight is kilogram (kg).

The factory default setting for the scales as supplied

is “kg”.

Slide the kg / lb / st switch to select the unit of

weight. The units will be displayed in the LC

display as follows:

Kilogram (kg): see Figure A

Pound (lb): see Figure E

Stone (st): see Figure F

Switching on your scales /

measuring your weight

Tip: Weigh yourself at the same time of day

(preferably in the morning) after visiting the toilet,

with an empty stomach and without clothing to

ensure that your results are compatible.

Place the scales down on a solid, ﬂat horizontal

surface.

Step on to the scales.

Place even weight on each leg.

If at all possible stand on the same areas of the

platform each time and do not move. Moving

during the weighing process can lead to

discrepancies in the results.

The scales will start to measure immediately.

After blinking 2 times, the weight display will

display the result, as shown in, for example,

Fig. B.

Note: If the scales show “OL” (see Fig. D), it

signals that the scales are overloaded. Observe

the maximum capacity of 180 kg (396 lb / 28 st).

Step oﬀ the platform. The scales switch oﬀ

automatically after about 10 seconds. Until

then the weight measurement remains visible.

Note: After a change of location and follow-

ing every battery change, the scales must be

re-calibrated. To do this, proceed as follows:

Step onto the scales. The scales will show you

an incorrect measuring result. Step oﬀ the plat-

form. The scales will calibrate automatically.

Wait until the scales switch oﬀ automatically.

Step onto the scales once again. The scales

will show you the correct measuring result.

Troubleshooting

This appliance has delicate electronic compo-

nents. This means that if it is placed near an

object that transmits radio signals, it could

cause interference. This could be, for example,

mobile telephones, walkie talkies, CB radios,

remote controls and microwaves. If the display

indicates a problem, move such objects away

from it.

Electrostatic charge can lead to the appliance

failing. In cases of the appliance failing to

work remove the batteries for a short while and

then replace them.

Cleaning

Do not use chemical cleaners or scouring

agents for cleaning the device.

Clean the device using a slightly moist cloth.

For more stubborn dirt you can also apply a

weak soap solution to the cloth.

Never immerse the device in water or other

liquids. Ignoring this advice may damage the

device.

Ensure that no water enters the device. If this

does occur, then wait until the device has dried

out fully before you use it again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest Z30936 IAN 75129 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest Z30936 IAN 75129

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info