Bedienungsanleitung Simrad Broadband 3G Radar (Seite 9 von 36) (Englisch)

634489

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation | Broadband 3G/4G™ Radar Installation Guide

Installation

 Note: Follow these instructions carefully. Don’t take any shortcuts!

• The Broadband Radar is factory sealed. It is not necessary to remove the cover.

• Removing the cover will void the factory warranty.

Tools Required

Choose the scanner location

The radar’s ability to detect targets greatly depends on the position of its scanner. The ideal

location for the scanner is high above the vessel’s keel line where there are no obstacles.

A higher installation position increases the radar ranging distance, but it also increases the

minimum range around the vessel where targets cannot be detected.

When you’re deciding on the location, consider the following:

The length of the interconnection cable supplied w your radar is usually su cient. If you think

you’ll need a longer cable, consult your dealer before installation. Optional cable lengths are 10

m (33 ft), 20 m (65.5 ft) and 30 m (98 ft).

If you mount the scanner on a pedestal or base, ensure that rain and sea spray can drain away

rapidly, and the breather hole in the base can operate .

The scanner is usually installed parallel to the line of the keel.

DON’T DO THIS!

• DON’T install the scanner too high up (eg at the top of a mast), which may cause

degradation of the radar picture over short ranges

• DON’T install the scanner close to lamps or exhaust outlets. The heat emissions may

damage the dome. Soot and smoke will degrade the performance of the radar

• DON’T install the scanner close to the antennas of other equipment such as direction

 nders, VHF antennas, GPS equipment, as it may cause or be subject to interference

• DON’T install the scanner where a large obstruction (such as an exhaust stack) is at the

same level as the beam, because the obstruction is likely to generate false echoes and/or

shadow zones

• DON’T install the scanner where it will be subjected to strong vibrations because these

vibrations could degrade the performance of the radar

• DON’T install the scanner such that boat electronics with switch mode power supplies

(such as  sh- nders and chart plotters) are in the beam of the antenna

• DON’T install the scanner directly on to a large  at roof area. Use a pedestal to elevate the

scanner for radar beams to clear roof line (see “Considerations for direct roof mounting” on

page 8)

Dual Radar installation - Broadband Radar and Pulse Radar installation:

For dual radar installations, ensure Broadband Radar is not installed in the beam of the pulse

radar at any time.

1. Drill

2. Torque wrench

3. Drill bit 9.5 mm (3/8”)

4. Screw driver

RADAR_3G_4G_IG_988-10113-003_EN_P.indd 7 2/11/2011 6:08:33 p.m.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Simrad Broadband 3G Radar Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info