Bedienungsanleitung Simrad WR10 (Seite 2 von 2) (Englisch)

634624

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Mounting location of base station

• Avoid installing the base station behind other electrical and electronic devices, as

they may interfere with the signal and consistency of wireless communication.

• The base station should be at least 2 meters away from any other Bluetooth or wire-

less LAN (WiFi) transceiver.

• It is advisable to check Bluetooth connection throughout the boat by pairing the

unit before permanently mounting the base station.

Operation

Keys and LED Action Mode: Auto Standby Wind NoDrift

< Left arrow Port or

> Right arrow Starboard

Short press: Adjust 1° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind mode.

√ √ √

Long press (2s): Adjust 10° to Port/Starboard i.e. heading in Auto mode, course in NoDrift mode and wind angle in Wind

mode.

√ √ √

< Left arrow +

> Right arrow

Autotack (in Wind mode), press and hold until LED is ﬂashing green rapidly, then press AUTO to conﬁrm.

√

STBY Place the autopilot into Standby mode. √ √ √

MODE Changes the autopilot mode:

1. Boats set to SAIL: Toggles AUTO and WIND modes. √ √

2. Other boat types: Toggles AUTO and NoDrift modes. √ √

AUTO Engages the autopilot into AUTO mode. √ √ √

LED* Green for 1s indicates message acknowledged. Red for 1s indicates message is either rejected or not acknowledged. √ √ √ √

Green rapid ﬂashes for up to 10s, followed by solid green for 1s. Red for 1s indicates message is either rejected or not

acknowledged.

√

* Note: In addition to the LED behaviour speciﬁed: Red will ﬂash for 1s every 10s when battery level is low.

X X

Electromagnetic

Interference

0.5 m (20”) Min 0.5 m (20”) Min

2 m (6 ft) Min

RADAR

Magnetic Field

Radio Transmitter

Surface mount the base station

3 mm

19 mm

Use of Lanyard strap or wristband Add/replace batteries

WR10 Wireless Autopilot Controller operates

on 2 AAA batteries. Remove the cover to add

or replace the batteries.

Wiring the base station

1.8 m (6 ft) Micro-C drop

cable (male to female)

Micro-C T-Joiner

Micro-C backbone

First, make sure that:

- the batteries in the remote are not low.

- the remote and the base station are placed as close together as possible.

- the AP system is OFF or in standby.

Then continue to:

1. Remove power from the base station.

2. Press and hold the buttons MODE and STBY on the remote for at least 5 seconds

until a single quick green LED ﬂashes. The remote is now in Discoverable mode and

will stay in this mode for 60 seconds or until base station asks to pair.

3. Power up base station. For the ﬁrst 10 seconds, the base station will search for

Discoverable remotes.

4. Wait till remote quickly ﬂashes the green LED every second, indicating that the base

station is asking to pair.

5. Press the AUTO button for at least 1 second to start the pairing.

- When succesfully paired: The green LED will stay on for 2 seconds.

- When pairing failed: The red LED will stay on for 2 seconds.

Pairing a remote to the base station

Use Philips screw-

driver size #1 to en-

sure proper torque

when reassembling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Simrad WR10 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info