Bedienungsanleitung Sitecom WL-118 Quick Start (Seite 18 von 38) (Englisch)

38870

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

ATM VC

• Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier)

define a virtual circuit.

• VPI: The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. This

field may already be configured.

• VCI: The valid range for the VCI is 32 to 65535. Enter the VCI assigned to you.

This field may already be configured.

• ATM QoS: Select CBR to specify fixed (always-on) bandwidth for voice or data

traffic. Select UBR for applications that are non-time sensitive, such as e-mail.

Select VBR for burst traffic and bandwidth sharing with other applications.

• PCR: Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the

Peak Cell Rate (PCR). This is the maximum rate at which the sender can send

cells.

• SCR: The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can

be transmitted.

• MBS: Maximum Burst Size (MBS) refers to the maximum number of cells that can

be sent at the peak rate. Type the MBS, which is less than 65535

Encapsulation:

• ISP: Select the encapsulation type your ISP uses from the Encapsulation list.

Choices vary depending on what you select in the Mode field.

If you select Bridge in the Mode field, select 1483 Bridged IP.

If you select Routing in the Mode field, select PPPoA, 1483 Bridged IP, 1483 Router IP

or PPPoE.

PPPoE/PPPoA

• User Name: Enter the user name exactly as your ISP assigned.

• Password: Enter the password associated with the user name above.

• Encapsulation: select Bridge in the Mode field, select either PPPoA or RFC 1483.

• select Routing in the Mode field, select PPPoA, RFC 1483, ENET ENCAP or PPPoE.

• Multiplex: Select the method of multiplexing used by your ISP. Choices are VC or

LLC.

• Connection: The schedule rule(s) have priority over your Connection settings.

• Always on: Select Always on Connection when you want your connection up all

the time.

• Connect on Demand: Select Connect on Demand when you don't want the

connection up all the time and specify an idle time-out in the Max Idle Timeout

field

• Get IP Address: Choose Static or Dynamic

• Static IP Address: Enter the IP address of ADSL Router in dotted decimal

notation, for example, 192.168.1.254 (factory default).

• IP Subnet Mask: The default is 255.0.0.0. User can change it to other such as

255.255.255.0.Type the subnet mask assigned to you by your ISP (if given).

• Gateway: You must specify a gateway IP address (supplied by your ISP) when

you use 1483 Bridged IP in the Encapsulation field in the previous screen.

• Network Address Translation: Select None, Many to One or Many to Many

from the drop-sown list box. Refer to the NAT chapter for more details.

• RIP Version: Select the RIP version from RIP-1, RIP-2B and RIP-2M.

• RIP Direction: Select the RIP direction from None, Both, In Only and Out Only.

• Multicast: IGMP (Internet Group Multicast Protocol) is a network-layer protocol

used to establish membership in a Multicast group - it is not used to carry user

data. The WL-118/WL-119 support both IGMP version 1 (IGMP-v1) and IGMP-v2.

Select None to disable it

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sitecom WL-118 Quick Start Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sitecom WL-118 Quick Start

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info