Bedienungsanleitung Sitecom WL-118 Quick Start (Seite 21 von 38) (Englisch)

38870

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Wireless LAN

• Access Point: Default setting is set to Activated. If you do not have any

wireless, 802.11g or 802.11b, device in your network, select Deactived.

• SSID: The SSID is the unique name of a wireless access point (AP) to be

distinguished from another. For security propose, change the default Sitecom to

a unique ID name to the AP which is already built-in to the router’s wireless

interface. It is case sensitive and must not excess 32 characters. Make sure your

wireless clients have exactly the SSID as the device, in order to get connected to

your network.

• Broadcast SSID: Select Yes to hide the SSID in so a station cannot obtain the

SSID through passive scanning. Select No to make the SSID visible so a station

can obtain the SSID through passive scanning.

• Channel ID: The range of radio frequencies used by IEEE 802.11b/g wireless

devices is called a channel. Select a channel from the drop-down list box.

• Authentication Type: To prevent unauthorized wireless stations from accessing

data transmitted over the network, the router offers highly secure data

encryption, known as WEP&WPA. If you require high security for transmissions,

there are three alternatives to select from: 64-bit WEP, 128-bit WEP, and

WPA. WPA offers the highest level of security available. WEP 128 will offer

increased security over WEP 64.

You can disable or enable with WPA or WEP for protecting wireless network. The

default type of wireless is disabled and to allow all wireless computers to

communicate with the access points without any data encryption

Advanced Setting

•

Beacon interval: The Beacon Interval value indicates the frequency interval of

the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast

by the Router to synchronize the wireless network.

RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes)

for enabling RTS/CTS handshake. Data with its frame size larger than this value

will perform the RTS/CTS handshake. Setting this attribute to be larger than the

maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake.

Setting this attribute to zero turns on the RTS/CTS handshake Enter a value

between 1500 and 2347..

Fragmentation Threshold: The threshold (number of bytes) for the

fragmentation boundary for directed messages. It is the maximum data fragment

size that can be sent. Enter a value between 256 and 2346.

DMIT: This value, between 1 and 255, indicates the interval of the Delivery

Traffic Indication Message (DTIM).

802.11b/g: The default setting is 802.11b+g (Mixed mode). If you do not know

or have both 11g and 11b devices in your network, then keep the default in

mixed mode. From the drop-down manual, you can select 802.11g if you have

only 11g card. If you have only 11b card, then select 802.11b.

Wireless MAC Address Filter

The MAC filter screen allows you to configure the router to give exclusive access to up to

32 devices (Allow Association) or exclude up to 32 devices from accessing the router

(Deny Association). Every Ethernet device has a unique MAC (Media Access Control)

address. The MAC address is assigned at the factory and consists of six pairs of

hexadecimal characters, for example, 00:AA:BB:11:22:34. You need to know the MAC

address of the devices to configure this screen.

To change your router’s MAC filter settings, click Wireless LAN, MAC Filter to open the

MAC Filter screen. The screen appears as shown.

• Active: Select Actived to enable MAC address filtering.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sitecom WL-118 Quick Start Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sitecom WL-118 Quick Start

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info