Bedienungsanleitung Skil 0230 (Seite 13 von 132) (Alle Sprachen)

757184

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

-clean line cutting blade N 2 and cutting guard A 2

after each use

-clean ventilation slots W 2 regularly with a brush or

compressed air

• Regularly check the condition of the cutting head and the

tightness of nuts, bolts and screws

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• Storage

Storage method 1 s

-securely mount storage rail Q on the wall with 2 screws

(not supplied) and horizontally leveled

-attach the storage adapter R and move it against the

mounting base of the storage rail Q

-store the tool with the storage hole in the handle over

the tip of the storage adapter

Storage method 2 u

-use pivot position 1 and let the tool stand by itself on

the ground

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

-send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

• Be aware that damage due to overload or improper

handling of the product will be excluded from the

warranty (for the SKIL warranty conditions see

www.skil.com or ask your dealer)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! in case of electrical or mechanical malfunction,



Tool does not operate

-empty battery -> charge battery

-hot battery -> let battery cool down

-internal fault -> contact dealer/service station

Tool operates intermittently

-internal wiring defective -> contact dealer/service

station

-      

Tool vibrates abnormally

-grass too high -> cut in stages

Tool does not cut

-        

Line cannot be fed

-spool empty -> replace spool

-line entangled inside spool -> inspect spool; rewind if

necessary

           

cutting blade

Line keeps breaking

-line entangled inside spool -> inspect spool; rewind if

necessary

-trimmer incorrectly used -> only trim with the tip of the

line; avoid stones, walls and other hard objects; feed

the line regularly

-keep the tool away from solid objects in order to protect

the cutting line against excessive wear

-be aware of the kickback forces that occur when solid

objects are touched

• Holding and guiding the tool o p

-for cutting long grass slowly swing the tool from right to

left and vice versa

-for cutting shorter grass tilt the tool as illustrated

-          

control of the tool at all times

-maintain a stable working position

-always hold the tool well away from your body

-for edging let the tool be supported by the edging

wheel S p

• Line feeding

The line is automatically fed when the tool is switched

  

-           

length by line cutting blade N

! take care against injury from line cutting blade N

•     a

-       

-pull the line and keep pulling, then press and release

the line feed button T

-after line feeding always return the tool to its normal

operating position before switching on

-feed the line regularly to maintain full cutting circle

-when the motor runs without load and no grass is cut,

the cutting line is stuck, worn or broken; rewind the

spool or replace the spool system

• Rewinding spool d

In case the cutting line fails to protrude from spool hole L

! 

-remove spool cover J and take out spool K from spool

holder V

-tightly rewind the cutting line evenly in layers in arrow

direction

-insert the cutting line into spool slot Z and ensure that it

        

-thread the cutting line through spool hole L before

placing the rewound spool into spool holder V

! ensure that the spool is located securely in place,

then pull the cutting line from slot Z

-mount spool cover J

• Replacing spool d

! 

-remove old spool and mount new spool as illustrated

-only use SKIL spool 2610S00818 with this tool

(damage due to using other spools will be

excluded from the warranty)

-after replacing the spool test-run the tool for at least

one minute without load to ensure that the tool is

operating properly

! 

battery

MAINTENANCE / SERVICE

• This tool is not intended for professional use

•         

ensure that all moving parts have come to a complete

standstill

• Always keep tool clean (especially ventilation slots W 2)

-clean the tool with a damp cloth (do not use cleaning

agents or solvents)

Skil 0230 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info