Bedienungsanleitung Skil 0320 (Seite 4 von 44) (Alle Sprachen)

701694

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite



LED Worklight 0320

INTRODUCTION

• The worklight is intended for

illumination in dry indoor areas

• This appliance is not intended for

professional use

• Check whether the packaging

contains all parts as illustrated in

drawing 6

• When parts are missing or damaged,

please contact your dealer

• Read this instruction manual carefully

before use and save it for future

reference 2

TECHNICAL DATA 1

Dimensions (width x depth x height) :

18.5 x 21.8 x 27.5 cm

Material shielding glass : tempered glass

APPLIANCE ELEMENTS 6

A Wing nut for assembly/xation

B Lamp head

C Stand

D Wing nuts for adjusting lighting angle

E Shielding glass

SAFETY

• Handletheworklightwithcare

• Donotdirectthelightbeamat

personsoranimalsanddonot

stareintothelightbeamyourself

(notevenfromadistance)

• Donotcoveroffthelamphead

whileoperatingtheworklight (the

lamp head heats up during operation

and can cause burns when the heat

accumulates)

• Replace damaged shielding glasses

before using the worklight again

• If the power cord is damaged, send

the worklight to a SKIL service station

(addresses are listed on www.skil.

com)

EXPLANATION OF SYMBOLS

2 Read the instruction manual before

use

3 Do not stare into the light beam

4 Replace a cracked shielding glass

5 Do not dispose of the worklight

together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG

(U.K. ONLY):

• Do not connect the blue (= neutral) or

brown (= live) wire in the cord of this

appliance to the earth terminal of the

plug

• If for any reason the old plug is cut o

the cord of this appliance, it must be

disposed of safely and not left

unattended

USE

• Assembly 6

! ensurethattheplugis

disconnectedfromthepower

sourcebeforeassemblingthe

appliance

- rst unscrew wing nut A

- assemble lamp head B on stand C

with wing nut A as illustrated

- lock the worklight in place by

tightening wing nut A

• Operating the appliance 6

- connect plug to power source

! connectthisearthedappliance

onlytoaproperlyearthed

powersupplysystem;ensure

thatsocketandextensioncable

haveafunctionalprotective

conductor

- the worklight is continuously

horizontally adjustable within its

pivoting range

- lock the worklight in place by

tightening wing nut A

- tilt the worklight into the desired

angle by loosening/tightening both

wing nuts D

MAINTENANCE / SERVICE

• This appliance is not intended for

professional use

• Clean the appliance with a dry or

slightly moist cloth (do not use any

abrasive or solvent-based cleaners)

! disconnecttheplugbefore

cleaning

• The light source of this appliance

cannot be replaced (if the LED-light

reaches the end of its service life after

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0320 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info