Bedienungsanleitung Skil 0700 (Seite 7 von 100) (Alle Sprachen)

591172

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

• Before use, thoroughly inspect the cutting area and

remove any object that the tool may sling during cutting

(such as stones, loose pieces of wood, etc.)

DURING USE

• Only use the tool in an vertical position, with the brush

pointing to the ground (neverswitchonthetoolin

anotherposition)

• Operate the tool at a walking pace only (do not run)

• Do not cross roads or gravel paths with the tool still

running

• Do not get distracted and always concentrate on what

you are doing

• Always ensure that the ventilation openings are kept clear

of debris

AFTER USE

• The brush continues to rotate for a short time after the

tool is switched o (donottouchtherotatingbrush)

• Always disconnect plug from power source

- whenever leaving the tool unattended

- before clearing jammed material

- before checking, cleaning or working on the tool

- after striking a foreign object

- whenever the tool starts vibrating abnormally

• Before you put down the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Store the tool indoors in a dry and locked-up place, out

of reach of children

EXPLANATIONOFSYMBOLSONTOOL

3Warning! Read the instruction manual

4 Do not expose tool to rain

5 Wear protective glasses and hearing protection

6 Payattentiontotheriskofinjurycausedbyflying

debris (keep bystanders a safe distance away from work

area)

7 Always keep hands and feet away from rotating parts

8 Switch o and disconnect plug before cleaning/

maintenance or if (extension) cord is damaged or

entangled

9 Double insulation (no earth wire required)

0 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

USE

• Assembly instructions

! alwaysdisconnecttheplugbeforemounting/

removingthebrush

- slide guard A over motor housing as illustrated until it

clicks into place !

- mount wheel B onto motor housing as illustrated until it

clicks into place @

- push spindle-lock button C and hold it while you

loosen collet nut D with wrench E #

- mount brush F with its centre in line with brush

indicator G

- tighten collet nut D with wrench E while pushing

spindle-lock button C

! replacethebrushwhenitisworn(SKIL

accessorynumber2610Z02973)

• Height adjustment $

- loosen locking sleeve H by turning it clockwise

! whenusingtoolforthefirsttime,rotatehandleK

90°afterlooseninglockingsleeveH

- extend tube J to the desired height

- tighten locking sleeve H by turning it counter-clockwise

! donotforcethetoolwhenextending/retracting

thetubetodesiredheight

• Cord restraint %

- hook the loop in the extension cord over restraint L as

illustrated

- pull tight to secure the extension cord

• On/o ^

- switch on tool by pressing trigger switch M

- switch o tool by releasing trigger switch M

! afterswitchingoffthetoolthebrushcontinuesto

rotateforafewseconds

- allow the brush to stop rotating before switching on

again

! donotrapidlyswitchonandoff

• Before using the tool

- ensure that brush F # is correctly mounted and that

collet nut D # is rmly tightened

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• Removing weed

! ensurethatthecuttingareaisfreeofstones,

debrisandotherforeignobjects

- ensure that the bottom side of the tool is kept in a level

position

- start working only when motor is running

- start working near the mains socket and move away

while working

- keep the tool away from solid objects and plants

- do not use the tool in one spot too long

- do not overload the tool

• Holding and guiding the tool &

- hold the tool rmly with one hand

- guide the tool at a constant speed over the surface to

be worked on

- maintain a stable working position

- always hold the tool well away from your body

APPLICATIONADVICE

• For best results test-run the tool on a small part of the

surface and check if the tiles do not get damaged

• Regular weeding helps to avoid persistent weed

• For more tips see www.skil.com

MAINTENANCE/SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean

! disconnecttheplugbeforecleaning

- regularly clean ventilation slots N 2 with a soft cloth

- regularly remove dirt from cutting guard A 2 with a

soft brush

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0700 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info