Bedienungsanleitung Skil 0705 (Seite 9 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

480092

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

• Ensure that the cutting blade is at a complete standstill

when tilting the tool for crossing surfaces other than

grass and when transporting it to and from the area to be

mowed

• Mow across the face of slopes (never up and down)

• Be extremely careful when changing direction on slopes

• Never pick up or carry the lawn mower while the motor is

running

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord

before disconnecting the plug)

• Never use the tool when cord is damaged; have it

replaced by a qualied person

USE

• Cord restraint #

- hook the loop in the extension cord over restraint B as

illustrated

- pull tight to secure the extension cord

• Adjusting cutting height (20-40-60 mm) $

! disconnect plug from power source and ensure

that the cutting blade has stopped rotating

- turn the mower upside down

- locate the two front wheels as well as the two rear

wheels into the desired cutting height position (20, 40

or 60 mm)

! ensure that the four wheels are fixed in the same

cutting height position

• On/o safety switch %

Prevents the tool from being switched on accidentally

- switch on tool by rst pressing safety switch D and

then pulling trigger switch E

- switch o tool by releasing trigger switch E

! after switching off the tool the blade continues to

rotate for a few seconds

• Operating instructions

- hold the mower with both hands

- place the mower on the edge of the lawn and mow in a

forward direction

- reverse at the end of each turn, slightly overlapping the

previous cut strip

- only use the mower on dry grass

- keep the mower away from solid objects and plants

- for mowing long grass, rst set the cutting mechanism

to the maximum cutting height, then to a lower cutting

height

! adjust your walking pace when mowing long

grass

• Storage ^

- for saving substantial storage space fold the tool

handle (using wing nut F 3) and store the tool as

illustrated; empty grass box first

! ensure that the (extension) cord is not trapped

when folding/unfolding the tool handle (do not

drop the handle)

- do not place other objects on top of the mower when

stored

- store the mower indoors in a dry place

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots J 3)

• Clean the mower after each use with a hand brush and a

soft cloth

! do not use water (especially no high-pressure

sprays)

- remove compacted grass cuttings from the blade area

with a wooden or plastic implement

• Regularly check the grass box for wear or damage

• Regularly check for worn or damaged blades and bolts

and have them replaced in sets to preserve balance

• Replacing the cutting blade &

! disconnect plug from power source and remove

grass box G 3

! wear protective gloves

- turn the mower upside down

- remove/mount the cutting blade with a spanner 13 as

illustrated

! only use replacement cutting blades of type

GD61BX.00.06 SKB

- thoroughly clean the shaft area and the underside of

the tool before mounting the cutting blade

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switch off the tool and disconnect the plug before

investigating the problem

★ Tool does not operate

- no power supply -> check power supply (power cable,

circuit breakers, fuses)

- power supply socket faulty -> use another socket

- extension cord damaged -> replace extension cord

- grass too high -> increase cutting height and tilt tool

★ Tool operates intermittently

- extension cord damaged -> replace extension cord

- internal wiring defective -> contact dealer/service

station

★ Tool leaves ragged nish or motor labours

- cutting height cut too low -> increase cutting height

- cutting blade blunt -> replace cutting blade

- underside of tool badly clogged -> clean tool

- cutting height not uniform -> set 4 wheels at same

cutting height

★ Cutting blade not rotating

- cutting blade obstructed -> clear obstruction

- blade nut/bolt loose -> tighten blade nut/bolt

★ Tool vibrates abnormally

- cutting blade damaged -> replace cutting blade

- blade nut/bolt loose -> tighten blade nut/bolt

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0705 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info