Bedienungsanleitung Skil 0711 (Seite 9 von 204) (Alle Sprachen)

699801

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

• Alwayskeephandsandfeetawayfromrotating

parts

• Keepawayfromthedischargeopeningatalltimes

• Do not transport the tool while the motor is running

• Always switch o tool, disconnect plug from power

source, and ensure that all moving parts have come to a

complete standstill

- whenever leaving the tool unattended

- before clearing jammed material

- before checking, cleaning or working on the tool

- after striking a foreign object

- whenever the tool starts vibrating abnormally

• If the cutting mechanism strikes any foreign object or if

the tool should start making any unusual noise or

vibration, immediately switch o, allow the cutting blade

to stop, disconnect the plug and take the following steps

- inspect for damage

- replace or repair any damaged parts

- check for and tighten any loose parts

AFTER USE

• Thecuttingbladecontinuestorotateforashort

timeaftertoolisswitchedoff(donottouchrotating

blade)

• Store the tool indoors in a dry and locked-up place, out

of reach of children

EXPLANATION OF SYMBOLS ON TOOL

4 Read the instruction manual before use

5 Double insulation (no earth wire required)

6 Wear protective glasses and hearing protection

7 Payattentiontotheriskofinjurycausedbyflying

debris (keep bystanders a safe distance away from work

area)

8 Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (donottouchthecord

beforedisconnectingtheplug)

9 Do not dispose of the tool together with household waste

material

USE

• Assembly instructions 2

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the lawn mower

! firmlytightenallscrews

- fasten screws A so that handle B moves freely

• Cord restraint 0

- hook the loop in the extension cord over restraint C as

illustrated

- pull tight to secure the extension cord

• Adjusting guide handle !

Handle B can be adjusted into the following three

positions

- ‘D’ (drive position) -> for mowing at exible working

height

- ‘P’ (park position) -> when emptying the grass box or

during work breaks

- ‘S’ (storage position) -> when storing the tool

• Adjusting cutting height (25-40-55 mm) @

! disconnectplugfrompowersourceandensure

thatthecuttingbladehasstoppedrotating

- put handle B 3 in storage position ‘S’

- turn the mower upside down

- locate the two front wheels as well as the two rear

wheels into the desired cutting height position (25, 40

or 55 mm)

- after adjusting cutting height, always check if grass

box E 3 is still securely in place

• On/o safety switch #

Prevents the tool from being switched on accidentally

- switch on tool by rst pressing safety switch F and

then pulling trigger switch G

- switch o tool by releasing trigger switch G

! afterswitchingoffthetoolthebladecontinuesto

rotateforafewseconds

• Operating instructions

- hold the mower with both hands

- place the mower on the edge of the lawn and mow in a

forward direction

- reverse at the end of each turn, slightly overlapping the

previous cut strip

- keep the mower away from solid objects and plants

! onlyusethemowerondrygrass

! formowinglonggrass,firstsetthecutting

mechanismtothemaximumcuttingheight,then

toalowercuttingheight

! adjustyourwalkingpacewhenmowinglong

grass

• Storage $

- for saving substantial storage space put handle B 3 in

storage position ‘S’ and store the tool as illustrated;

emptygrassboxfirst

- do not place other objects on top of the mower when

stored

- store the mower indoors in a dry place

- always allow the tool to cool down before storing

• Replacing cutting blade %

- disconnect plug from power source

- simply remove/mount old/new cutting blade as

illustrated

- after replacing the cutting blade test-run the tool for at

least one minute without load to ensure that the tool is

operating properly

! onlyusereplacementcuttingbladesofthe

correcttype(SKILaccessory2610Z04031/BOSCH

accessoryF016800183)

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Keep all nuts, bolts and screws tight to be sure that the

tool is in a safe working condition

• Regularly check the grass box for wear or damage

• Alwaysdisconnectplugfrompowersourcebefore

cleaningand/ormaintenance

• Beawarethatduringcleaning/maintenance(even

thoughthetoolisswitchedoff)thecuttingblade

canstillbemoved

• Always keep tool and cord clean (especially ventilation

slots H 3)

• Clean the mower after each use with a hand brush and a

soft cloth

- remove compacted grass cuttings from the blade area

with a wooden or plastic implement

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0711 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info