Bedienungsanleitung Skil 0720 (Seite 5 von 44) (Alle Sprachen)

591145

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite



Hand mower 0720

INTRODUCTION

• This product is intended for domestic lawn mowing only

! do not use the hand mower to cut grass on roofs

or balconies

• Check whether the packaging contains all parts as

illustrated in drawing 2

• When parts are missing or damaged, please contact

your dealer

TECHNICAL SPECIFICATIONS 1

TOOL ELEMENTS 2

A Push bar

B Cutting blades

C Foldable grass collector

D Holding belt

E Wing nut for adjusting mowing height

F Screw for adjusting bottom blade

G Bottom blade

SAFETY

• Read this instruction manual carefully before use and

save it for future reference 3

• Take care when transporting the mower to the lawn, as

the cutting blades are sharp

• Always wear long trousers when mowing

• Do not operate the mower when barefoot or wearing

open sandals

• Thoroughly inspect the area where the mower is to be

used and remove all hard objects which could be caught

up and thrown by the cutting mechanism

• Always ensure that the cutting mechanism is in good

working order (have worn or damaged parts replaced)

• Keep all nuts, bolts and screws tight to be sure that the

mower is in safe working condition

• Only mow with sucient daylight or with appropriate

articial lighting

• Never mow in the direct vicinity of persons (especially

children) and animals

• Always keep hands and feet away from rotating parts

• Operate the mower at a walking pace only (do not run)

• Keep proper footing on slopes and do not mow extremely

steep slopes

• Be extremely careful when moving backwards or pulling

the mower towards you

• Never leave the mower unattended

• Never let children or other persons who are not familiar

with the operating instructions use the product

USE

• Assembly instructions 4

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the hand mower

! firmly tighten all screws and nuts

• Adjusting cutting height (12 - 44 mm) 5

! wear protective gloves

- place the mower on a rm, at surface

- loosen both wing nuts E

- lift the housing in the center to the required

cutting height

- adjust the cutting height so that bottom blade G has no

ground contact if there are uneven areas on the

lawn surface

- tighten both wing nuts E

! ensure that wing nuts E are adjusted at the same

height on both sides

• Operating instructions

- hold the mower with both hands

- place the mower on the edge of the lawn and mow in a

forward direction

- reverse at the end of each turn, slightly overlapping the

previous cut strip

- only use the mower on dry grass

- keep the mower away from hard objects and plants

- for mowing long grass, rst set the cutting mechanism

the maximum cutting height, then to a lower

cutting height

- adjust bottom blade G when the grass is not cut

cleanly and evenly

• Adjusting bottom blade 6

! prevent entrapment of the fingers between

moving cutting blades and fixed parts of the

mower

! wear protective gloves

- turn the mower upside down

- adjust bottom blade G to the required position by

loosening/tightening both adjustment screws F

- the adjustment is correct, if a piece of paper inserted

between cutting blades B and bottom blade G is cut

sharp like through a pair of scissors (to do this

carefully rotate the blade cylinder by hand)

MAINTENANCE / SERVICE

• Clean the mower after each use with a hand brush and a

soft cloth

! do not use water (especially no high-pressure

sprays)

- remove compacted grass cuttings from the blade area

with a wooden or plastic implement

• Lubricate the cutting blades regularly to avoid oxydation

• Regularly check for loose or damaged cutting blades,

and worn or damaged components

• The mower is equipped with self-sharpening

cutting blades

! be aware that the self-sharpening function does

not work, when bottom blade G is not correctly

adjusted (see 6)

• When necessary, take the mower to your dealer to have

the cutting mechanism sharpened

• Store the mower indoors in a dry place

• Do not place other objects on top of the mower when stored

• If the appliance should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0720 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info