Bedienungsanleitung Skil 0780 AA (Seite 11 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

480087

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

- do not over reach and do not cut above shoulder

height (this helps prevent unintended tip contact

and enables better control of the chain saw in

unexpected situations)

- only use replacement bars and chains specified

by the manufacturer (incorrect replacement bars

and chains may cause chain breakage and/

or kickback)

- follow the manufacturer’s sharpening and

maintenance instructions for the saw chain

(decreasing the depth gauge height can lead to

increased kickback)

PERSONAL SAFETY

• It is recommended that the rst time user should have

practical instruction in the use of the chainsaw and the

protective equipment from an experienced operator and

that the initial practice should be cutting logs on a saw

horse or cradle

• Do not touch rotating chain

• Do not operate chain saw near other people,

children or animals

• Do not operate chain saw after drinking alcohol

or under the influence of intoxicating drugs

or medication

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the tool by a person responsible

for their safety

• Ensure that children do not play with the tool

ELECTRICAL SAFETY

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Only use an extension cord which is intended for

outdoor use and equipped with a watertight plug

and coupling-socket

• Only use extension cords with a maximum length of

20 metres (1,5 mm²) or 50 metres (2,5 mm²)

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord

before disconnecting the plug)

• Protect the (extension) cord from heat, oil and

sharp edges

• Never use the cord for carrying, pulling or unplugging

the tool

• Inspect the cord periodically and have it replaced by

a qualied person, if damaged

• Inspect the extension cord periodically and replace it,

if damaged (inadequate extension cords can

be dangerous)

• Do not use the tool if the switch does not turn it on and

o; always have a damaged switch repaired by a

qualied person

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Always switch off tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord before

disconnecting the plug)

5 Do not expose tool to rain

6 Wear protective glasses and hearing protection

7 Double insulation (no earth wire required)

8 Do not dispose of the tool together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Assembly 9

! do not connect the chain saw to mains before

it is completely assembled

! always use gloves when handling the chain

- place the chain saw on any suitable at surface

- remove cover plate A by turning locking knob

B counter-clockwise

- slide chain C in the slot around chain bar D

! ensure chain is in correct running direction by

comparing with chain symbol E

- t the chain onto drive sprocket F and guide chain

bar D, so that fastening bolt G and the two guide

ns H t into the keyway of chain bar D, and that

chain tensioning peg J ts into the respective hole

of chain bar D

- if necessary, turn tensioning knob K to bring tensioning

peg J in alignment with the hole in chain bar D

- check if all parts are seated properly and hold chain

and chain bar in a level position

- turn tensioning knob K until all the slack is taken up in

the chain

- mount cover plate A as illustrated

- tighten locking knob B on fastening bolt G by turning

it clockwise

• Tensioning chain 0

- place the chain saw on any suitable at surface

- check if the chain links are correctly located in the slot

around chain bar D

1) loosen locking knob B until it is just holding chain bar

in position (do not remove)

2) lift the chain bar somewhat and hold it in that position

3) turn chain tensioning knob K upwards until the lowest

chain links come up and JUST touch the bottom of

chain bar D

4) tighten locking knob B by turning it clockwise

5) release chain bar

6) the correct chain tension is reached when the chain can

be raised approx. 4 mm from the chain bar in the centre

! always check the chain tension before use, after

the first cuts and regularly during use (approx.

every 10 minutes)

- upon initial operation, new chains can

lengthen considerably

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0780 AA Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info