Bedienungsanleitung Skil 1061 (Seite 12 von 116) (Alle Sprachen)

701628

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

6 Laser radiation / Do not stare into beam / Class 2

laser product

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/o 7

• Speed control for smooth starting 8

• Switch locking for continuous use 9

• Changing saw blades 0

! insert blade to full depth with teeth facing forward

! use T-shank blades only

• Sawing at 15°/30°/45° @

• Adjusting sawing speed to material used #

! if the tool does not run with wheel D in position 1,

select a higher sawing speed and lower the

sawing speed while the tool runs

• Dust suction $

- connect vacuum cleaner to extension E

! do not use vacuum cleaner when cutting metal

• Selecting sawing mode %

Use lever F 2 for adjusting the orbital action from

accurate cutting (= 0) to fast cutting (= III)

- 1 setting (“0”) for accurate cutting in all materials,

straight + curved

- 3 settings for fast cutting in dierent materials, straight

cuts only

I = metal

II = plastic

III = hard wood

! always select “0” when sawing splinter-sensitive

material

• Laser line ^

- for guiding tool along desired line of cut marked on the

workpiece

- switch on/o laser line by pressing switch G

- before starting a job, check the alignment of the laser

line with the actual line of cut by making a trial cut on a

piece of waste material

! do not attempt to adjust the laser line with screw

X which is pre-set at manufacturing

! do not remove or damage warning label A 2

• Operating the tool

- before switching on the tool, ensure that front end of

footplate rests at on the workpiece

- hold tool rmly with both hands, so you will have full

control of the tool at all times

! while working, always hold the tool at the

grey-coloured grip area(s) &

- ensure that complete surface of footplate rests rmly

on the workpiece

! ensure that the blade has come to a complete

standstill, before you lift the tool from the

workpiece

- keep ventilation slots H 2 uncovered

APPLICATION ADVICE

• Use the appropriate saw blades *

! use T-shank blades only

• When cutting metals, lubricate saw blade regularly with oil

• Use parallel guide J for making parallel cuts (

• For an accurate straight cut, guide tool with footplate along

the edge of a straight piece of wood )

• Pre-drill a hole before making cut-outs ¡

• Splinter-free cutting

- cover cutting-line with several layers of wide tape before

cutting

- always face the good side of the workpiece down

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation slots

H 2)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law, electric

tools that have reached the end of their life must be

collected separately and returned to an environmentally

compatible recycling facility

- symbol 5 will remind you of this when the need for

disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound

pressure level of this tool is 88 dB(A) and the sound power

level 99 dB(A) (standard deviation: 3 dB), and the vibration

✱ (triax vector sum; uncertainty K = 1.5 m/s²)

✱ when cutting wood 6.7 m/s²

✱ when cutting metal 11.4 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 62841; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when using

the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1061 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info