Bedienungsanleitung Skil 1144 (Seite 10 von 148) (Alle Sprachen)

701698

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

• Mounting of accessories 8

! disconnect the plug

- clean spindle C and all parts to be mounted

- screw VELCRO backing pad D onto spindle C while

pushing spindle-lock button E

! push spindle-lock button E only when spindle C

is at a standstill

- simply press polishing pad F, G or H onto VELCRO

backing pad D

- for removing accessories handle vice-versa

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 60 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o

- switch on/o the tool by pulling/releasing trigger J 2

• Electronic soft-start

Ensures reaching the maximum speed smoothly without

a sudden impact when tool is switched on

• Switch locking for continuous use

- pull trigger J

- press knob K with your thumb

- unlock the switch by pulling again trigger J and then

releasing it

• Speed control 9

- with wheel L the maximum speed can be adjusted

from low to high (1-6)

- start with wheel L in position 1 (lower speed)

- if needed, select a higher speed while the tool runs

- the optimal working speed depends on the material

and can be determined with practical trials

• Operating the tool

- switch on the tool

- place the tool fully on the surface to be polished and

move it evenly by sections

- one move should overlap the previous move by one

half

- do not stop at a single spot to avoid burning the

coating

- do not move the tool in circles to avoid staining or

burning the coating

! before switching off the tool, you should lift it

from the workpiece

! the accessory continues to rotate for a short time

after the tool has been switched off

! dirty polishing pads cause swirl marks, so keep

them clean

• Holding and guiding the tool 0

! while working, always hold the tool at the

grey-coloured grip area(s)

- always hold the tool rmly with both hands, so you will

have full control of the tool at all times

- provide for a secure stance

! do not apply so much pressure on the tool that it

comes to a standstill

- keep ventilation slots M 2 uncovered

APPLICATION ADVICE

• For optimal results !

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Protect the tool from impact, shock and grease

• Always keep tool and cord clean (especially ventilation

slots M 2)

! disconnect the plug before cleaning

! do not attempt to clean ventilation slots by

inserting pointed objects through openings

• Clean the polishing pads with water after use

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 6 will remind you of this when the need for

disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 98 dB(A) and the sound

power level 109 dB(A) (standard deviation: 3 dB), and the

vibration 4.8 m/s² (triax vector sum; uncertainty K = 1.5

m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1144 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info