Bedienungsanleitung Skil 1470 AA (Seite 7 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

482543

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

• Mounting of sanding sheet 6

- knock the dust out of the VELCRO material on sanding

pad C 2 before mounting the sanding sheet

- mount VELCRO sanding sheet as illustrated

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total VELCRO

surface covered with sanding paper

• Dust/chip extraction 7

- mount dust extraction device D as illustrated

- connect vacuum cleaner

! do not use dust extraction device/vacuum cleaner

when sanding metal

- clean dust extraction device D regularly for optimal

dust pick-up performance

• On/o

- switch on/o the tool by pushing switch E 2 in

"I"/"O" position

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

• Adjusting working speed 8

- with wheel F the required oscillating frequency can be

adjusted from low (1) to high (6) (also while tool

is running)

- the optimal working speed depends on the material

and can be determined with practical trials

• Holding and guiding the tool

! while working, always hold the tool at the

grey-coloured grip area(s) 9

- keep ventilation slots G 2 uncovered

- do not apply too much presssure on the tool

(excessive pressure will cause excessive heat and

may shorten the service life of the accessory)

APPLICATION ADVICE

• Use segment saw blade H 2 for separating and plunge

cuts in wood, plaster, gypsum and plastics (also for

sawing close to edges, in corners and other hard-to-

reach areas)

• Use plunge-cut saw blade J 2 for separating and deep

plunge-cuts in wood, plaster, gypsum and soft plastics

(also for sawing close to edges, in corners and other

hard-to-reach areas)

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots G 2)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 0 will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this product

is in conformity with the following standards or

standardized documents: EN 60745, EN 61000,

EN 55014, in accordance with the provisions of the

directives 2004/108/EC, 2006/42/EC, 2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/PJE),

4825 BD Breda, NL

ÊÆÇÎ¹Æ¼½ÊÄÇÇÌ

Á»½Ê½ËÁ¼½ÆÌ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

¹ÆÊÇÅÅ½Ä½Æ

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

02.02.2012

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 92 dB(A) and the sound

power level 103 dB(A) (standard deviation: 3 dB),

and the vibration ✱ (hand-arm method)

✱ when sanding 8.8 m/s² (uncertainty K = 1.5 m/s²)

✱ when cutting with plunge-cut saw blade 13.9 m/s²

(uncertainty K = 1.5 m/s²)

✱ when cutting with segment saw blade 7.2 m/s²

(uncertainty K = 1.5 m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintainted accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1470 AA Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info