Bedienungsanleitung Skil 1480 Multitool (Seite 12 von 116) (Alle Sprachen)

701638

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Changing accessories 7

! disconnect the plug

- remove/mount the required accessory as illustrated

- ensure that the openings of the accessory engage into

the tabs of the tool head (any snap-in position

possible)

- mount the accessory with the depressed centre

pointing downwards

- take hex key A from storage B 2

- loosen/fasten screw C with hex key A

- check the tight seating of the accessory (incorrect

or not securely fastened accessories can come loose

during operation and create a hazard)

• Mounting of sanding sheet 8

- tap the dust out of the VELCRO material on sanding

pad D before mounting the sanding sheet

- mount VELCRO sanding sheet E as illustrated

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total VELCRO

surface covered with sanding paper

• Mounting of auxiliary handle F 9 (1480)

! disconnect the plug

- screw auxiliary handle F on the right or the left of the

tool (depending on the work to be carried out)

• Dust suction 0

! disconnect the plug

- use dust extraction device G only when working with

sanding pad D

- mount dust extraction device G as illustrated

- connect vacuum cleaner

! do not use dust extraction device/vacuum cleaner

when sanding metal

- clean dust extraction device G regularly for optimal

dust pick-up performance

• On/o

- switch on/o the tool by pushing switch H 2 in “I”/”O”

position

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

• Adjusting working speed !

- with wheel J the required oscillating frequency can be

adjusted from low (1) to high (6) (also while tool is

running)

- the optimal working speed depends on the material

and can be determined with practical trials

• Holding and guiding the tool

! while working, always hold the tool at the

grey-coloured grip area(s) @

- keep ventilation slots K uncovered

- do not apply too much pressure on the tool (excessive

pressure will cause excessive heat and may shorten the

service life of the accessory)

• Depth adjustment accessory (DEPTH STOP) (not

standard included) #

APPLICATION ADVICE

• For optimal results on dierent materials use table $ as

reference for determining the right accessory (accessories

not standard included)

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation slots

K 2)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law, electric

tools that have reached the end of their life must be

collected separately and returned to an environmentally

compatible recycling facility

- symbol 6 will remind you of this when the need for

disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound

pressure level of this tool is 91.0 dB(A) and the sound power

level 102.0 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)

✱ when sanding 4.5 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 62841; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when using

the tool for the applications mentioned

- using the tool for dierent applications, or with dierent or

poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1480 Multitool Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info