Bedienungsanleitung Skil 1590 (Seite 10 von 116) (Alle Sprachen)

758610

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Never use the tool when the cord is damaged; it must be

replaced by a specially prepared cord available through

the service organization.

• Always disconnect plug from power source before

making any adjustment or changing any accessory

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Before using the tool check that the knives do not brush

anywhere

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Keep your ngers away from the rotating knives

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• If any chip should get jammed in the chip outlet, you

should switch o the motor, ensure that all moving parts

have come to a complete standstill, disconnect the plug,

and remove the jammed chip

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

•If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Changing/reversing knives 6

This planer is equipped with non-grindable knives with

cutting edges on both sides; so if one side has become

blunt, the other side can be used

! 

-remove guiding devices, if mounted

-take wrench from storage A 6 a

-turn tool upside down

-loosen 3 bolts B with wrench (do not remove bolts) 6 b

-push knife out of cutter block with piece of wood 6 c

-put knife back in cutter block in reversed position, or

use new knife 6 d

! groove in knife should match ledge in cutter block

! place knives against support plate R 6 e

-rmly tighten 3 bolts B with wrench 6 f

! change/reverse knives in time; only use sharp

knives

! always change/reverse both knives at the same

time

 Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage



power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5) SERVICE

a) 

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR PLANERS

• Wait for the cutter to stop before setting the tool

down (an exposed rotating cutter may engage the

surface leading to possible loss of control and serious

injury)

• Hold the power tool by insulated gripping surfaces,

because the cutter may contact its own cord (cutting

a “live” wire may make exposed metal parts of the power

tool “live”and could give the operator an electric shock)

• Use clamps or another practical way to secure and

support the workpiece to a stable platform (holding

the workpiece by your hand or against the body leaves it

unstable and may lead to loss of control)

GENERAL

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A);

wear ear protection

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

Skil 1590 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info