Bedienungsanleitung Skil 1734 (Seite 10 von 116) (Alle Sprachen)

591189

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

off-load; however, the accessory automatically

centres itself during operation without affecting

drilling precision

! do not use bits with a damaged shank

• Selecting operating mode 0

1 = normal drilling/screwdriving

2 = hammer drilling

! select operating mode only when tool is switched

off and plug is disconnected

- the hammer mechanism is activated by applying a

slight pressure on the tool when the drill bit is in

contact with the workpiece

- it takes a short time for the hammer mechanism to

reach full impact power

- best hammer drilling results can be obtained by only a

slight pressure on the tool; drilling performance will not

improve by applying more pressure on the tool

• Adjusting drilling depth !

• Holding and guiding the tool @

! while working, always hold the tool at the

grey-coloured grip area(s)

- always use auxiliary handle H (can be adjusted as

illustrated)

- keep ventilation slots J 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits #

! only use sharp bits

• For drilling in wood, metal and plastic as well as for

screwdriving use an adapter (not standard included) $

! clean and lightly lubricate the SDS+ adapter

before insertion

- pull back locking sleeve D 2 and insert adapter in

SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch F 2 to normal drilling (only activate when

tool is switched off and plug is disconnected)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• Splinterfree drilling in wood %

• Dustfree drilling in walls ^

• Dustfree drilling in ceilings &

• Drilling in tiles without skidding *

• For more tips see www.skil.com

• For drilling in wood, metal and plastic as well as for

screwdriving use an adapter (not standard included) $

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol ( will remind you of this when the need for

disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product

described under “Technical data” is in conformity with the

following standards or standardization documents: EN

60745, EN 61000, EN 55014, in accordance with the

provisions of the directives 2004/108/EC, 2006/42/EC,

2011/65/EU

• Technical file at: SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

¹ÊÁÂÆÎ¹Æ¼½ÊÇÇ¾¼½Æ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

Ä¹¾ÁÂÃ¿Ê¹¹¾

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

23.10.2014

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 88 dB(A) and the sound

power level 99 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)

✱ when hammer drilling in concrete 12 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1734 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info