Bedienungsanleitung Skil 1735 (Seite 8 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

479901

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

• Changing bits 0

! cleanandlightlylubricatetheSDS+accessory

beforeinsertion

- pull back locking sleeve F 2 and insert accessory in

SDS+ chuck while turning and pushing it until it

engages; the accessory locks in position automatically

- pull accessory to check that it is locked correctly

- remove accessory by pulling back locking sleeve F

! theSDS+accessoryrequiresfreedomof

movementwhichcauseseccentricitywhentoolis

off-load;however,theaccessoryautomatically

centresitselfduringoperationwithoutaffecting

drillingprecision

! donotusebitswithadamagedshank

• Safety clutch

If the accessory gets jammed, the drive to the spindle is

interrupted (causing a rattling noise)

- immediately switch o tool

- remove the jammed accessory

- switch on tool again

• Adjusting drilling depth !

• Holding and guiding the tool @

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)

- alwaysuseauxiliaryhandleG2

(can be adjusted as illustrated)

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool;

let the tool do the work for you

APPLICATIONADVICE

• Use the appropriate bits #

! onlyusesharpbits

• For drilling in wood, metal and plastic as well as for

screwdriving use the corresponding adapter

(SKIL accessory 2610395660) $

- clean and lightly lubricate adapter before insertion

- pull back locking sleeve F 2 and insert adapter in

SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch E 2 to normal drilling (onlyactivatewhen

toolisswitchedoffandplugisdisconnected)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• Splinterfree drilling in wood %

• Dustfree drilling in walls ^

• Dustfree drilling in ceilings &

• Drilling in tiles without skidding *

• For more tips see www.skileurope.com

MAINTENANCE/SERVICE

• Always keep tool and cord clean

(especially the ventilation slots)

! disconnecttheplugbeforecleaning

• If the tool should fail despite the care taken in manufacturing

and testing procedures, repair should be carried out by an

after-sales service centre for SKIL power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skileurope.com)

ENVIRONMENT

• Donotdisposeofelectrictools,accessoriesand

packagingtogetherwithhouseholdwastematerial

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol ( will remind you of this when the need for

disposing occurs

DECLARATIONOFCONFORMITY

• We declare under our sole responsibility that this

product is in conformity with the following standards

or standardized documents: EN 60745, EN 55014,

in accordance with the provisions of the directives

2006/95/EC, 2004/108/EC, 2006/42/EC

• Technicalfileat: SKIL Europe BV (PT-SEU/PJE),

4825 BD Breda, NL

ÊÆÇÎ¹Æ¼½ÊÄÇÇÌ

Á»½Ê½ËÁ¼½ÆÌ

È½Ê¹ÌÁÇÆËŵÆ¿ÁÆ½½ÊÁÆ¿

ÍÊÇÈ½Ɠˁ˅ʿ˂Ê½¼¹Ɠ

¹ÆÊÇÅÅ½Ä½Æ

ÈÈÊÇÎ¹Ä¹Æ¹¿½Ê

26.04.2011

NOISE/VIBRATION

• Measured in accordance with EN 60745 the sound

pressure level of this tool is 91 dB(A) and the sound

power level 102 dB(A) (standard deviation: 3 dB), and the

vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)

✱ when impact drilling in concrete 15.5 m/s²

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60745; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintainted accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protectyourselfagainsttheeffectsofvibration

bymaintainingthetoolanditsaccessories,

keepingyourhandswarm,andorganizingyour

workpatterns

Skil 1735 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skil 1735

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info