Bedienungsanleitung Skil 1740 (Seite 8 von 14) (Englisch)

479902

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

! select operating mode only when tool is switched

off

- for drilling in wood, metal and plastic as well as for

screwdriving the corresponding adapter should be

used (see: Application Advice)

- the hammer mechanism is activated by applying a

slight pressure on the tool when the drill bit is in

contact with the workpiece

- best hammer drilling results can be obtained by only

a slight pressure on the tool needed to keep the

automatic clutch engaged; drilling performance will

not improve by applying more pressure on the tool:

SKIL LETS THE TOOL WORK FOR YOU

• Changing bits 0

- clean and lightly lubricate accessory before insertion

- pull back locking sleeve F 2 and insert accessory in

SDS+ chuck while turning and pushing it until it

engages; the accessory locks in position

automatically

- pull accessory to check that it is locked correctly

- remove accessory by pulling back locking sleeve F

! the SDS+ accessory requires freedom of

movement which causes eccentricity when tool is

off-load; however, the accessory automatically

centres itself during operation without affecting

drilling precision

! do not use bits with a damaged shank

• Safety clutch

If the accessory gets jammed, the drive to the spindle is

interrupted (causing a rattling noise)

- immediately switch off tool

- remove the jammed accessory

- switch on tool again

• Adjusting drilling depth !

• Holding and guiding the tool @

- always use auxiliary handle G 2 (can be adjusted

as illustrated)

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

APPLICATION ADVICE

• Use the appropriate bits #

! only use sharp bits

• For drilling in wood, metal and plastic as well as for

screwdriving use the corresponding adapter (SKIL

accessory 2610395660) $

- clean and lightly lubricate adapter before insertion

- pull back locking sleeve F 2 and insert adapter in

SDS+ chuck while turning and pushing it until it

engages; the adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch E 2 to normal drilling (only activate when

tool is switched off)

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• Splinterfree drilling in wood %

• Dustfree drilling in walls ^

• Dustfree drilling in ceilings &

• Drilling in tiles without skidding *

• For more tips see www.skileurope.com

GUARANTEE / ENVIRONMENT

• Always keep tool and cord clean (especially the

ventilation slots)

! disconnect the plug before cleaning

• This SKIL product is guaranteed in accordance with

statutory/country-speciﬁ c regulations; damage due to

normal wear and tear, overload or improper handling will

be excluded from the guarantee

• In case of a complaint, send the tool undismantled

together with proof of purchase to your dealer or the

nearest SKIL service station (addresses as well as the

service diagram of the tool are listed on

www.skileurope.com)

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol ( will remind you of this when the need for

disposing occurs

Perforateur 1735/1740

INTRODUCTION

• L’outil est conçu pour le perçage de percussion dans le

béton, la brique et dans la pierre naturelle; pour le

perçage dans le bois, le métal et les matières plastiques

ainsi que pour le vissage il est nécessaire d’utiliser des

accessoires spéciﬁ ques

• Le système de percussion de cet outil surpasse

largement la performance des perceuses à percussion

traditionelles lorsqu’il est utilisé dans le béton

• Cet outil convient parfaitement pour une utilisation avec

tous les accessoires SDS+ standards

• Lisez et conservez ce manuel d’instructions 3

SPECIFICATIONS TECHNIQUES 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1740 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skil 1740

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info