Bedienungsanleitung Skil 1745 (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

479903

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

INTRODUCTION

● This tool is intended for hammer drilling in concrete, brick

and stone; for drilling in wood, metal and plastic as well

as for screwdriving specific accessories should be used

● The hammering system in this tool outperforms any

traditional ratcheting drill when drilling in concrete

● This tool is designed for use in combination with all

standard SDS+ accessories

TECHNICAL SPECIFICATIONS 1

OPERATING CONTROLS 2

A Switch for on/off and speed control

B Button for switch locking

C Lever for changing direction of rotation

D Switch for selecting drilling function

E Dust cap

F Locking sleeve

G Auxiliary handle

H Wing nut for adjusting auxiliary handle

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always keep the cord away from moving parts of the tool

● When you put away the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Before using accessories always compare the maximum

allowed r.p.m. of that specific accessory with the r.p.m.

of the tool

● This tool should not be used by people under the age of

16 years

● Be careful not to drill or drive into areas where electrical

wires may be contacted; always use auxiliary

handle G 2

● The noise level when working can exceed 85 dB(A);

wear ear protection

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

● Never use tool when cord is damaged; have it replaced

by a qualified person

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● Be aware of the forces that occur as a result of jamming

(especially when drilling metals); always use auxiliary

handle G 2 and take a secure stance

● Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● On/Off 3

● Switch locking for continuous use 4

● Speed control for smooth starting 5

● Changing direction of rotation 6

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

● Normal drilling/screwdriving versus hammer drilling 7

! select drilling function only when tool is switched

off

- for drilling in wood, metal and plastic as well as for

screwdriving the ring gear chuck and the corresponding

adapter should be used (see: Application Advice)

- the hammer mechanism is activated by applying a

slight pressure on the tool when the drill bit is in

contact with the workpiece

- best hammer drilling results can be obtained by only

a slight pressure on the tool needed to keep the

automatic clutch engaged; drilling performance will

not improve by applying more pressure on the tool:

SKIL LETS THE TOOL WORK FOR YOU

● Changing bits 8

- clean and lightly lubricate accessory before insertion

- insert accessory in SDS+ chuck while turning and

push it until it engages (avoid damaging dust cap E);

the accessory locks in position automatically

- pull accessory to check that it is locked correctly

- remove accessory by pushing back locking sleeve F

! the SDS+ accessory requires freedom of

movement which causes eccentricity when tool is

off-load; however, the accessory automatically

centres itself during operation without affecting

drilling precision

! do not use bits with a damaged shank

● Safety clutch

If the accessory gets jammed, the drive to the spindle is

interrupted (causing a rattling noise)

- immediately switch off tool

- remove the jammed accessory

- switch on tool again

● Adjusting drilling depth 9

● Holding and guiding the tool 0

! always use auxiliary handle G 2 (can be adjusted

with wing nut H)

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

XP SKIL 1745/1750 27-03-2003 14:14 Pagina 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1745 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info