Bedienungsanleitung Skil 1763 (Seite 13 von 124) (Alle Sprachen)

758387

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/o 6

• Switch locking for continuous use 7

• Speed control for smooth starting 8

• Maximum speed control 9

With wheel B 5 the maximum speed can be adjusted

steplessly from minimum to maximum

• Changing direction of rotation 0

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Selecting operating mode !

- press button F to unlock switch E

- turn switch E to the desired operating mode until it

snap-locks

! start working only when switch E is locked

1 = normal drilling/screwdriving

2 = impact drilling

3 = chiseling with rotating chisel

4 = chiseling with xed chisel

! select operating mode only when tool is switched

off and plug is disconnected

- the hammer mechanism is activated by applying a

slight pressure on the tool when the drill bit is in

contact with the workpiece

- best hammer drilling results can be obtained by only a

slight pressure on the tool; drilling performance will not

improve by applying more pressure on the tool

• Chiseling with rotating chisel @

! switch off the tool and disconnect the plug

- select “rotating” chiseling mode

• Chiseling with xed chisel #

! switch off the tool and disconnect the plug

- select “rotating” chiseling mode

- place chisel in desired position

- select “xed” chiseling mode

• Changing bits $

! clean and lightly lubricate the SDS+ accessory

before insertion

- pull back locking sleeve G and insert accessory in

SDS+ chuck while turning and pushing it until it

engages; the accessory locks in position automatically

- pull accessory to check that it is locked correctly

- remove accessory by pulling back locking sleeve G

! the SDS+ accessory requires freedom of

movement which causes eccentricity when tool is

off-load; however, the accessory automatically

centres itself during operation without affecting

drilling precision

! do not use bits/chisels with a damaged shank

For drilling in wood, metal and plastic as well as for

screwdriving use adapter H %

- clean and lightly lubricate adapter before insertion

- pull back locking sleeve G and insert adapter in SDS+

chuck while turning and pushing it until it engages; the

adapter locks in position automatically

- pull adapter to check whether is it locked correctly

- set switch E 5 to normal drilling (only activate when

tool is switched off and plug is disconnected)

• Safety clutch

If the accessory gets jammed, the drive to the spindle is

interrupted (causing a rattling noise)

- immediately switch o tool

- remove the jammed accessory

- switch on tool again

• Adjusting drilling depth ^

• Holding and guiding the tool &

! while working, always hold the tool at the

grey-coloured grip area(s)

- always use auxiliary handle J (can be adjusted as

illustrated)

- keep the ventilation slots uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits *

! only use sharp bits/chisels

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• Splinterfree drilling in wood (

• Dustfree drilling in walls )

• Dustfree drilling in ceilings ¡

• Drilling in tiles without skidding ™

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots K 5)

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1763 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info