Bedienungsanleitung Skil 1845 (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

427103

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Router 1845

INTRODUCTION

● The tool is intended to route grooves, edges, profiles and

elongated holes in wood, plastic and light building

materials as well as to copy-route

TECHNICAL SPECIFICATIONS 1

SAFETY

GENERAL

● Read and save this instruction manual (pay special

attention to the safety instructions at the back)

● This tool should not be used by people under the age of

16 years

● Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

● Do not use damaged or deformed router bits

● Only use sharp router bits

● Protect accessories from impact, shock and grease

● Only use high speed steel (HSS) or carbide-tipped (CT)

router bits with this tool

BEFORE USE

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

● Do not work with materials containing asbestos

● Clamp the workpiece in case it does not remain

stationary from its own weight

● Do not clamp the tool in a vice

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● The noise level when working can exceed 85 dB(A);

wear ear protection

● Wear a dust protection mask when working with

materials which produce dust that is detrimental to

health; inform yourself beforehand about the materials to

be worked on

● Be sure tool is switched off when plugging in

DURING USE

● Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

● Never use tool when cord or base-plate M 2

(=protective guard) is damaged; have it replaced by a

qualified person

● Keep hands and fingers away from router bit when tool is

switched on

● Never exceed maximum cutting depth of router bit

(= B 0) while cutting

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● In case the router bit is blocked, resulting in jerking

forces on the tool, immediately switch off the tool

● In case of current interruption or when the plug is

accidentally pulled out, immediately put the on/off switch

in the “O”-position in order to prevent uncontrolled

restarting

● Do not apply so much pressure on the tool that it comes

to a standstill

AFTER USE

● After finishing the work, loosen handle E 2, guide the

tool back into the upper starting position, and switch off

the tool

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this

tool, it must be disposed of safely and not left unattended

USE

● Mounting/removing router bits 3

! switch off the tool and disconnect the plug

! ensure that router bit shaft is perfectly clean

! ensure that collet size corresponds with shaft size

of router bit

- turn tool upside down

- lock shaft by pushing shaft lock A (rotate collet nut B,

if necessary) and hold it while you

FOR MOUNTING:

- loosen collet nut B with wrench C

- insert bit 3/4 in collet D

- tighten collet nut firmly with wrench C

FOR REMOVING:

- loosen collet nut B with wrench C

- pull bit out of collet D

- release shaft lock A

! for loosening router bit it may be necessary to tap

collet nut with wrench 4

! never tighten collet nut, if there is no router bit in

collet; collet may be damaged

● Changing collet 3

! switch off the tool and disconnect the plug

! ensure that collet shaft is perfectly clean

- turn tool upside down

- remove collet nut B (lock shaft)

- pull collet D out of collet nut B

- insert new collet in collet nut B until it snap-locks

- mount collet nut B (lock shaft)

● Adjusting routing depth 2

EXAMPLE

Desired routing depth 7 mm

- loosen handle E

- loosen wing nut F so that depth gauge G moves freely

- push tool down until router bit is in contact with

workpiece and tighten wing nut F

- note value as indicated on depth scale (e.g. 35 mm)

(for zeroing)

XP SKIL 1845 21-03-2003 15:31 Pagina 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1845 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info