Bedienungsanleitung Skil 2017 (Seite 9 von 128) (Alle Sprachen)

591179

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

APPLICATION ADVICE

 Use the appropriate bits

! only use sharp bits

 When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

 When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

 For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

 When screwdriving in hard wood one should pre-drill a

hole

 Splinterfree drilling in wood

 Dustfree drilling in walls

 Dustfree drilling in ceilings

 Drilling in tiles without skidding

 For more tips see www.skil.com

MAINTENANCE / SERVICE

 This tool is not intended for professional use

 Keep tool and charger clean

- clean charging contacts in charger with alcohol or

contact cleaner

! unplug charger from power source before

cleaning

 If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skil.com)

- in case of a defective charger send both charger and

battery to your dealer or the SKIL service station

ENVIRONMENT

 Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC

on waste of electric and electronic equipment and

its implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol

will remind you of this when the need for

disposing occurs

 The battery must be kept separate from the natural

environment and should not be disposed of as normal

domestic waste (symbol

will remind you of this when

the need for disposing occurs)

! prior to disposal protect battery terminals with



Do not dispose of the charger together with household

waste material

Do not dispose of the battery together with household

waste material

USE

 Charging battery

- battery of new tools is not fully charged

- connect charger to power source as illustrated

- green light G will turn on indicating that the charger is

ready for operation

- insert battery into charger

- red light H will turn on indicating that the battery is

being charged

- charge the battery for at least 5 hours, after which

the battery may be used even though the red light

may still be on (the red light may require more than 5

hours to turn o)

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

! a battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles

- do not repeatedly recharge the battery after only a few

minutes of operation; this may result in a reduction of

operating time and battery eciency

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

 On/o

 Speed control for smooth starting

 Changing direction of rotation

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

 Changing bits

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

 Torque control (VariTorque)

- limits the amount of output torque delivered by the

chuck (21 clutch settings)

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

 Holding and guiding the tool

! 

coloured grip area(s)

- keep ventilation slots E

uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2017 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info