Bedienungsanleitung Skil 2236 (Seite 7 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

381371

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

USE

• Charging battery 8

- battery of new tools is not fully charged

- connect charger to power source as illustrated

! unplug the charger from the tool after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well

as the charger

! a battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles

- do not repeatedly recharge the battery after only a

few minutes of operation; this may result in a

reduction of operating time and battery efﬁ ciency

- the nickel-cadmium battery must be kept separate

from the natural environment and should not be

disposed of as normal domestic waste (symbol 7

will remind you of this when the need for disposing

occurs)

! prior to disposal protect battery terminals with

heavy tape to prevent short-circuit

- if you anticipate long periods of non-use for the tool,

it is best to unplug the charger from its power source

• On/Off & Changing direction of rotation 9

• Changing bits 0

- push bit to end position in bitholder

! never use bits shorter than 30 mm

! do not use bits with a damaged shank

• Automatic spindle-lock

Allows you to manually tighten or loosen screws,

when necessary !

• Two handle positions @

1 - for normal screwdriving

2 - for screwdriving in hard-to-reach places

- for optimal results when tightening/loosening

screws manually

APPLICATION ADVICE

• Use the appropriate bits #

! do not use damaged bits

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill a

hole

• For more tips see www.skileurope.com

• Vibration level

The vibration emission level stated at the back of this

instruction manual has been measured in accordance

with a standardised test given in EN 60745; it may be

used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintainted accessories, may

signiﬁ cantly increase the exposure level

- the times when the tool is switched off or when it is

running but not actually doing the job, may

signiﬁ cantly reduce the exposure level

! protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

MAINTENANCE / SERVICE

• Keep tool and charger clean

! unplug charger from power source before

cleaning

• If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on

www.skileurope.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 6 will remind you of this when the need for

disposing occurs

! remove the batteries before disposal of the tool $

- dispose of the batteries at an ofﬁ cial collection point

for batteries

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2236 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info