Bedienungsanleitung Skil 2244 (Seite 8 von 136) (Alle Sprachen)

644733

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

5 Double insulation (no earth wire required)

6 Batteries may explode when disposed of in fire, so do not

burn battery for any reason

7 Store tool/charger/battery in locations where temperature

will not exceed 50°C

8 Do not dispose of the charger together with household

waste material

9 Do not dispose of the battery together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not left

unattended

USE

• Combined switch A 2 for on/o and speed control

Control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery 0

- connect charger to power source as illustrated

- green light B will turn on indicating that the charger is

ready for operation 0a

- insert battery into charger as illustrated 0b

! the battery can also remain in the tool while

charging; in that case the tool cannot be switched

- green light B will blink indicating that the battery is

being charged 0c

- after approximately 1 hour the battery is fully charged

and green light B stays on after blinking 0d

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- if green light B does not blink after inserting a battery,

this may mean:

1) that the battery is too cold or too hot (charger only

charges batteries when its temperature is between

0°C and 45°C)

2) that the battery should be replaced

- the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not damage

the battery)

- the lithium-ion battery does not have to be empty

before charging (no “memory-eect” as with

nickel-cadmium batteries)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

- when the lithium-ion battery is empty, the tool is

switched o automatically

- a signicantly reduced working period after charging

indicates that the battery is worn out and should be

replaced

• Changing direction of rotation !

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing drill bits @

- insert the bit as deep as possible in the chuck

- use screw bits in combination with a bitholder

! do not use bits with a damaged shank

! only use sharp bits

• Torque control (VariTorque) #

- output torque will increase as clutch ring C is rotated

from 1 to 15; position D will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection $

- set selector F to desired speed

! actuate the gear selector while tool is running

slowly

HIGH POWER

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

HIGH SPEED

- lower torque

- for drilling small diameters

• Battery level indicator %

- shows how much energy the battery has left

- indicator G automatically lights on when activating

switch A 2

• Spot light H ^

Spot light H automatically lights on when activating

switch A 2

• Battery protection

Switches o the tool automatically when

1) the load is too high

2) the battery temperature is not within the allowable

operating temperature range of -10 to +60°C

3) the lithium-ion battery is nearly empty (to protect

against deep discharge)

- in either case the 3 LED-lights of battery level indicator

G will ash rapidly

! do not continue to press the on/off switch after

the tool is switched off automatically; battery may

be damaged

• Automatic spindle-lock

- when switch A 2 is not pressed, the spindle is locked

- allows you to use the tool as a screwdriver (even when

the battery is empty)

• Holding and guiding the tool &

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots J 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2244 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info