Bedienungsanleitung Skil 2395 (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388617

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

INTRODUCTION

● This tool is intended for drilling in wood, metal, brick,

stone, ceramic and plastic; tools with electronic speed

control and left/right rotation are also suitable for

screwing and thread cutting

TECHNICAL SPECIFICATIONS 1

OPERATING CONTROLS 2

A Switch for on/off and speed control

B Switch for changing direction of rotation

C Keyless chuck

D Ring for torque control

SAFETY

● Read and save this instruction manual (pay special

attention to the safety instructions at the back) 3

● Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

● Check voltage indicated on nameplate of tool/charger/

battery

● In case of electrical or mechanical malfunction,

immediately switch off the tool or unplug charger from

power source

● SKIL can assure flawless functioning of the tool only

when original accessories are used

● Before using accessories always compare the maximum

allowed r.p.m. of that specific accessory with the r.p.m.

of the tool

● This tool should not be used by people under the age of

16 years

● Be careful not to drill or drive into areas where electrical

wires may be contacted

● Do not activate switch when changing accessories or

carrying the tool

CHARGING/BATTERIES

● Charge battery only with the charger that is supplied

with the tool

● Do not touch the contacts in the charger

● Do not expose tool/charger/battery to rain

● Never charge battery outdoors 4

● Store tool/charger/battery in locations where

temperature will not exceed 40° C or drop below 0° C

● Batteries will explode in fire, so do not burn battery for

any reason

● When damaged, and under extreme usage and

temperature conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly

with soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, flush eyes with clean water

for a minimum of 10 minutes and seek immediately

medical attention

● When battery is not in tool or charger, it should be kept

away from metal objects such as nails, screws, keys etc.

to prevent short-circuit

● Do not use charger when damaged; take it to one of the

officially registered SKIL Service Stations for a safety

check

● Do not use charger when cord or plug is damaged; cord

or plug should be replaced immediately at one of the

officially registered SKIL Service Stations

● Do not use battery when damaged; it should be replaced

immediately

● Do not disassemble charger or battery

● Do not attempt to recharge non-rechargeable batteries

with the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the

plug

● If for any reason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left

unattended

USE

● Charging battery 5

- battery of new tools is not fully charged

! remove battery from charger after charging period

has ended thereby lengthening the service life of

the battery

IMPORTANT:

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0° C and over

40° C; this will seriously damage the battery as well

as the charger

- do not remove battery from tool while it is running

- when you charge the battery for the first time, it only

accepts 80% of its maximum capacity; after several

charges and discharges, however, the batteries

should be at full capacity and deliver maximum

performance

- do not repeatedly recharge the battery after only a

few minutes of operation; this may result in a

reduction of operating time and battery efficiency

- the nickel-cadmium battery must be kept separate from

the natural environment and should not be disposed of

as normal domestic waste (symbol 6 will remind you

of this when the need for disposing occurs)

! prior to disposal protect battery terminals with

heavy tape to prevent short-circuit

- if you anticipate long periods of non-use for the tool,

it is best to unplug the charger from its power source

● On/Off 7

● Speed control for smooth starting 8

● Changing direction of rotation 9

- when not properly set in left/right position, switch A

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

● Changing bits 0

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

XP SKIL 2295/2395/2495 28-05-2002 11:58 Pagina 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2395 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info