Bedienungsanleitung Skil 2532AA (Seite 9 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

482531

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

• Charging battery 0

! a lithium-ion battery that is new or has not been

used for a longer period does not develop its full

capacity until after approximately 3 charging/

discharging cycles

- connect charger to power source as illustrated 0a

- green light B will turn on indicating that the charger is

ready for operation 0a

- insert battery into charger as illustrated 0b

! the battery can also remain in the tool while

charging; in that case the tool cannot be switched on

- green light B will blink indicating that the battery is

being charged 0c

- after approximately 1 hour the battery is fully charged

and green light B stays on after blinking, at which time

the charger automatically switches to maintenance-

charging 0d

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- if green light B does not blink after inserting a battery,

this may mean that the battery is too cold or too hot

(charger only charges batteries when its temperature is

between 0°C and 45°C); the charger then automatically

switches to maintenance-charging, until a temperature

between 0°C and 45°C is reached, at which time the

charger will automatically switch to normal charging 0e

- the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not damage

the battery)

- the lithium-ion battery does not have to be empty

before charging (no “memory-eect” as with

nickel-cadmium batteries)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

- when the lithium-ion battery is empty, the tool is

switched o automatically

- a signicantly reduced working period after charging

indicates that the battery is worn out and should

be replaced

• Changing direction of rotation !

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits @

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) #

- output torque will increase as clutch ring C is rotated

from 1 to 19

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

- position D will lock up the clutch to permit (non-impact)

drilling or driving heavy-duty work

- position E will lock up the clutch to permit impact

drilling only

! ensure that gear selector G is in position HIGH

when clutch ring C is in impact drilling position

! do not use impact drilling position E for drilling in

wood, metal, ceramic and plastic to prevent the

drill/screw bit from being damaged

• Mechanical gear selection $

- set selector G to desired speed

! actuate the gear selector while tool is

running slowly

LOW

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

HIGH

- high speed

- lower torque

- for impact drilling

- for drilling small diameters

• Battery protection

Switches o the tool automatically when

1) the load is too high

2) the battery temperature is not within the allowable

operating temperature range of -10 to +60°C

3) the lithium-ion battery is nearly empty (to protect

against deep discharge)

! do not continue to press the on/off switch after

the tool is switched off automatically; battery may

be damaged

• Spot light H %

Spot light H automatically lights on when activating

switch A 2

• Holding and guiding the tool ^

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots J 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits &

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill

a hole

• Splinterfree drilling in wood *

• Dustfree drilling in walls (

• Dustfree drilling in ceilings )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2532AA Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info