Bedienungsanleitung Skil 2536 (Seite 8 von 164) (Alle Sprachen)

591182

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

9 Do not dispose of the battery

together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG

(U.K. ONLY):

• Do not connect the blue (= neutral) or

brown (= live) wire in the cord of the

charger to the earth terminal of the

plug

• If for any reason the old plug is cut o

the cord of the charger, it must be

disposed of safely and not left

unattended

USE

• Charging battery 0

- battery of new tools is not fully

charged

! unplug the charger from the

tool after charging period has

ended thereby lengthening the

service life of the battery

IMPORTANT:

- while charging, the charger and the

battery may become warm to

touch; this is normal and does not

indicate a problem

- do not charge at temperatures

below 0°C and over 45°C; this will

seriously damage the battery as

well as the charger

! a lithium-ion battery that is new

or has not been used for a

longer period does not develop

its full capacity until after

approximately 3 charging/

discharging cycles

- connect charger B with both wall

socket and contact C

- charging light D turns on indicating

that the tool is being charged

- when the battery is fully charged,

charging light D turns o (after

5 hours)

- the lithium-ion battery can be

charged at any time (interrupting

the charging procedure does not

damage the battery)

- the lithium-ion battery does not

have to be empty before charging

(no “memory-eect” as with

nickel-cadmium batteries)

- if you anticipate long periods of

non-use for the tool, it is best to

unplug the charger from its power

source

• On/o !

• Changing direction of rotation @

- when not properly set in left/right

position, the tool will not operate

! change direction of rotation

only when tool is at a complete

standstill

• Changing bits #

- push bit to end position in bitholder

! do not use bits with a damaged

shank

• Automatic spindle-lock

Allows you to manually tighten or

loosen screws, when necessary $

• Spot light G %

Spot light G automatically lights on

when activating switch A 2

• Two handle positions ^

• Battery protection

Switches o the tool automatically

when

1) the load is too high

2) the battery temperature is not

within the allowable operating

temperature range of -10 to +60°C

3) the lithium-ion battery is nearly

empty (to protect against deep

discharge)

! do not continue to press the on/

off switch after the tool is

switched off automatically;

battery may be damaged

APPLICATION ADVICE

• Use the appropriate bits &

! do not use damaged bits

! only use bits with hexagon shaft

• When turning in a screw at/near the

cross cut end or an edge of wood,

pre-drill a hole in order to avoid

cracking of the wood

• For an optimal use of the tool a steady

pressure on the screw is required,

especially while removing

• When screwdriving in hard wood one

should pre-drill a hole

• For more tips see www.skileurope.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2536 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info