Bedienungsanleitung Skil 2842 (Seite 10 von 128) (Alle Sprachen)

758369

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

-the battery temperature is not within the allowable

operating temperature range of -20 to +50°C

-the lithium-ion battery is nearly empty (to protect

against deep discharge)

! 



damaged

• LED-light F e

-LED-light F automatically lights on when activating

switch A

• Holding and guiding the tool r

! while working, always hold the tool at the grey-

coloured grip area(s)

-keep ventilation slots G 2 uncovered

-do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits t

! only use sharp bits

• When drilling ferrous metals

-pre-drill a smaller hole, when a large hole is required

-lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill a

hole

• Splinterfree drilling in wood y

• Dustfree drilling in walls u

• Drilling in tiles without skidding i

• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots G 2)

! remove battery from tool before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

-send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

• Be aware that damage due to overload or improper

handling of the tool will be excluded from the warranty

(for the SKIL warranty conditions see www.skil.com or

ask your dealer)

ENVIRONMENT

• Do not dispose of electric tools, batteries,

accessories and packaging together with household

waste material (only for EU countries)

-in observance of European Directive 2012/19/EC

on waste of electric and electronic equipment and

its implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

• Only use the following batteries and chargers with

this tool

-SKIL battery: BR1*31****

-SKIL charger: CR1*31****

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

-when charging 4...40°C

-during operation –20...+50°C

-during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3 Read the instruction manual before use

4 Batteries may explode when disposed of in re, so do not

burn battery for any reason

5 Store tool/charger/battery in locations where temperature

will not exceed 50°C

6 Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A 2

-control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Battery level indicator 7

-press the battery level indicator button H to show the

current battery level.

• Changing direction of rotation 8

-when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits 9

! do not use bits with a damaged shank

• Torque control (VariTorque) q

-output torque will increase as clutch ring B is rotated

from 1 to 23; position C will lock up the clutch to permit

drilling or driving heavy duty work

-when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection w

-set selector D to desired speed

! actuate the gear selector while tool is running

slowly

-low speed

-high torque

-for screwdriving and drilling large diameters

-for tapping thread

-high speed

-lower torque

-for impact drilling

-for drilling small diameters

• Battery protection

Switches o the tool or prevents the tool from being

switched on, when

-the load is too high

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2842 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info