Bedienungsanleitung Skil 3018 (Seite 10 von 136) (Alle Sprachen)

758373

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

-the load is too high --> remove load and restart

-the battery temperature is not within the allowable

operating temperature range of -20 to +50°C --> 2

levels of the battery level indicator start ashing when

pressing button N 8c; wait until battery has returned

within the allowable operating temperature range

-the battery is nearly empty (to protect against

deep discharge) --> a low battery level or ashing low

battery level 8b is shown by the battery level indicator

when pressing button N; charge battery

! 



damaged

• Changing direction of rotation 9

-when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits q

! do not use bits with a damaged shank

• Torque control (VariTorque) w

-output torque will increase as clutch ring B is rotated

from 1 to 17

-when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

-position F will lock up the clutch to permit (non-impact)

drilling or driving heavy-duty work

-position D will lock up the clutch to permit impact

drilling only

! ensure that gear selector B is in position 2 when

function selector C is in impact drilling position

! do not use impact drilling position D for drilling in

wood, metal, ceramic and plastic to prevent the

drill/screw bit from being damaged

• Mechanical gear selection e

-set selector G to desired speed

! actuate the gear selector while tool is running

slowly

-low speed

-high torque

-for screwdriving and drilling large diameters

-for tapping thread

-high speed

-lower torque

-for impact drilling

-for drilling small diameters

• Holding and guiding the tool t

! while working, always hold the tool at the grey-

coloured grip area(s)

-keep ventilation slots J 2 uncovered

-do not apply too much pressure on the tool; let the tool

do the work for you

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots H 2)

! remove battery from tool before cleaning

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

DURING USE

• In case of electrical or mechanical malfunction,

immediately switch o the tool or unplug charger from

power source

BATTERIES

• The battery supplied is partially charged (to ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

-SKIL battery: BR1*31****

-SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

-when charging 4...40°C

-during operation –20...+50°C

-during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3 Read the instruction manual before use

4 Batteries may explode when disposed of in re, so do not

burn battery for any reason

5 Store tool/charger/battery in locations where temperature

will not exceed 50°C

6 Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A 2

-control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Attaching belt clip 7

-attach the belt clip L to the drill with the supplied screw.

• Battery level indicator 8

-press the battery level indicator button N to show the

current battery level 8a

! when the lowest level of the battery indicator

8b, the

battery is empty

! 

after pressing button N 8c, the battery is not

within the allowable operating temperature range

• LED-light M r

LED-light M automatically lights on when activating

switch A

! 

protection is activated (see below)

Skil 3018 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info