Bedienungsanleitung Skil 3020 (Seite 10 von 136) (Alle Sprachen)

758370

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

drilling or driving heavy-duty work

-position D will lock up the clutch to permit impact

drilling only

! ensure that gear selector B is in position 2 when

function selector C is in impact drilling position

! do not use impact drilling position D for drilling in

wood, metal, ceramic and plastic to prevent the

drill/screw bit from being damaged

• Mechanical gear selection e

-set selector G to desired speed

! actuate the gear selector while tool is running

slowly

-low speed

-high torque

-for screwdriving and drilling large diameters

-for tapping thread

-high speed

-lower torque

-for impact drilling

-for drilling small diameters

• Battery protection

Switches o the tool or prevents the tool from being

switched on, when

-the load is too high

-the battery temperature is not within the allowable

operating temperature range of -20 to +50°C

-the lithium-ion battery is nearly empty (to protect

against deep discharge)

! 



damaged

• LED-light M r

-LED-light M automatically lights on when activating

switch A r

• Holding and guiding the tool t

! while working, always hold the tool at the grey-

coloured grip area(s)

-keep ventilation slots J 2 uncovered

-do not apply too much pressure on the tool; let the tool

do the work for you

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots H 2)

! remove battery from tool before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

-send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

• Be aware that damage due to overload or improper

handling of the tool will be excluded from the warranty

(for the SKIL warranty conditions see www.skil.com or

ask your dealer)

APPLICATION ADVICE

• Use the appropriate bits y

! only use sharp bits

clamping devices or in a vice is held more securely than

by hand)

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

DURING USE

• In case of electrical or mechanical malfunction,

immediately switch o the tool or unplug charger from

power source

BATTERIES

• The battery supplied is partially charged (to ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

-SKIL battery: BR1*31****

-SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

-when charging 4...40°C

-during operation –20...+50°C

-during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3 Read the instruction manual before use

4 Batteries may explode when disposed of in re, so do not

burn battery for any reason

5 Store tool/charger/battery in locations where temperature

will not exceed 50°C

6 Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A 2

-control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Attaching belt clip 7

-attach the belt clip L to the drill with the supplied screw.

• Battery level indicator 8

-press the battery level indicator button N to show the

current battery level.

• Changing direction of rotation 9

-when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits q

! do not use bits with a damaged shank

• Torque control (VariTorque) w

-output torque will increase as clutch ring B is rotated

from 1 to 17

-when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

-position F will lock up the clutch to permit (non-impact)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 3020 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info