Bedienungsanleitung Skil 3265 (Seite 9 von 128) (Alle Sprachen)

797791

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

-LED-light turns on when activating on/o switch E, or

pressing either LED-light button F or mode button G

-Press LED-light button to select desired brightness:

Low brightness – turns o approx. 10s after on/o

switch is released

High brightness - turns o approx. 600s after on/o

switch is released

! When LED-light starts ashing rapidly, the battery

protection is activated (see above)

• Mode selection r

-press the mode button G to select the desired mode:

Low speed mode (light “1” shines green) ra

-tightening with less torque and low speed

-for small bolts and screws

Medium speed mode (lights “1&2” shine green) rb

-tighten with medium torque and speed

-for the screws in medium-duty application

High speed mode (lights “1&2&3” shine green) rc

-tightening with high force and speed

-for large screws and bolts

Reverse control mode (light “RM” shines green) rd

-for loosening bolts and nuts

-stops when the bolt or nut is loosened

! control mode is only available with reverse

rotation; in forward rotation it is used for high

speed

! modes can only be changed when green LED(s)

are activated and when the tool is at a complete

standstill

• Installing and removing sockets t

-to install a socket, simply push it onto to square drive D

-to remove a socket, simply pull it o square drive D

! only use sockets with a 3/8” square drive ta

! use adapter M for sockets with a 1/2" square drive

! do not use damaged sockets

• Holding and guiding the tool y

! while working, always hold the tool at the grey-

coloured grip area(s)

-keep ventilation slots B2 uncovered

-do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill a

hole

• For more information see www.skil.com

MAINTENANCE/SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots B2)

! Remove battery from tool before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

-send the tool undismantled together with proof of

• Only use the following batteries and chargers with

this tool

-SKIL battery: BR1*31****

-SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced immediately

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

-when charging 4...40°C

-during operation -20…+50°C

-during storage -20…+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3 Read the instruction manual before use

4 Batteries may explode when disposed of in re, so do not

burn battery for any reason

5 Store tool/charger/battery in locations where temperature

will not exceed 50°C

6 Do not dispose of electric tools and batteries together

with household waste material

USE

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Battery level indicator 7

-press the battery level indicator button H to show the

current battery level 7a

! when the lowest level of the battery indicator

starts ashing after pressing button H7b, the

battery is empty

! when 2 levels of the battery indicator start ashing

after pressing button H7c, the battery is not

within the allowable operating temperature range

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

-the load is too high --> remove load and restart

-the battery temperature is not within the allowable

operating temperature range of -20 to +50°C -->2

levels of the battery level indicator start ashing when

pressing button H7c; wait until battery has returned

within the allowable operating temperature range

-the battery is nearly empty (to protect against

deep discharge) --> a low battery level or ashing low

battery level 7b is shown by the battery level indicator

when pressing button H; charge battery

! do not continue to press the on/o switch after the

tool is switched o automatically; battery may be

damaged

• Attaching belt clip 8

-attach the belt clip L to the wrench with the supplied

screw

• Changing direction of rotation 9

-when not properly set in left/right position, switch E2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Combined switch for on/o q and speed control w

-control the speed steplessly from zero to maximum by

putting less or more pressure on the E2

• LED-light e

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 3265 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info