Bedienungsanleitung Skil 3335-01 (Seite 6 von 52) (Englisch, Französisch, Spanisch)

758357

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

General Specifications

Voltage Rating . . . . . . . . . . . . . . . . . . .120 V, 60 Hz

Amperage Rating . . . . . . . . . . . . . . . . . . . . . . .1.2 A

No Load Speed . . . . . . . . .No500-1,700/min (SPM)

Throat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16"

Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . .5” pin-end

Blade Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . .7/8"

Cutting Capacity . . . . . . . . . . . . . . . . . . . . .2" at 90°

Table Tilt . . . . . . . . . . . . . . . . . . . . . . . 0° to 45° Left

Motor Specifications

In the event of a malfunction or breakdown, grounding pro-

vides a path of least resistance for electric current to reduce

the risk of electric shock. This tool is equipped with an elec-

tric cord having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into a match-

ing outlet that is properly installed and grounded in accor-

dance with all local codes and ordinances.

This Scroll Saw is designed to use a 1700 RPM motor. It is

wired for operation on 110-120 volts, 60 Hz. alternating cur-

rent. Before connecting the motor cord to power source,

make certain the switch is in the “OFF” position and be sure

the electric current is of the same characteristics as

stamped on the scroll saw nameplate.

Connection ToAPower Source

This machine must be grounded while in use to protect the

operator from electric shock.

Plug power cord into a 110-120V properly grounded type

outlet protected by a 15-amp dual element time delay fuse

or circuit breaker.

Not all outlets are properly grounded. If you are not sure

that your outlet, as pictured in Fig. 1, is properly

grounded; have it checked by a qualified electrician.

To avoid electric shock, do not touch

the metal prongs on the plug when

installing or removing the plug to or from the outlet.

Failure to properly ground this power

tool can cause electrocution or seri-

ous shock, particularly when used near metal

plumbing or other metal objects. If shocked, your

reaction could cause your hands to hit the tool.

If power cord is worn, cut or damaged

in any way, have it replaced immedi-

ately to avoid shock or fire hazard.

Your unit is for use on 120 volts; it has a plug that looks

like the one in Figure 1.

This power tool is equipped with a 3-conductor cord and

grounding type plug, approved by Underwriters

Laboratories and the Canadian Standards Association.

The ground conductor has a green jacket and is

attached to the tool housing at one end and to the

ground prong in the attachment plug at the other end.

If the outlet you are planning to use for this power tool is

of the two-prong type, DO NOT REMOVE OR ALTER

THE GROUNDING PRONG IN ANY MANNER.. Have a

qualified electrician replace the TWO-prong outlet with a

properly grounded THREE-prong outlet.

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. The con-

ductor with insulation having an outer surface that is

green with or without yellow stripes is the equipment-

conductor. If repair or replacement of the electric cord or

plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if

the grounding instructions are not completely under-

stood, or if in doubt as to whether the tool is properly

grounded.

Always use proper extension cord. The use of any exten-

sion cord will cause some loss of power. To keep this to

aminimum and to prevent overheating and motor burn-

out, use the table below to determine the minimum wire

size (A.W.G.) extension cord. Use only 3-wire extension

cords which have 3-prong grounding type plugs and 3-

pole receptacles which accept the tool’s plug. Make sure

your extension cord is in good condition.

Extension Cord Length Wire Size A.W.G.

0-25 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

26-50 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

51-100 feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Motor Specifications and Electrical Requirements

“SAVE THESE INSTRUCTIONS”

DANGER

WARNING

FIG. 1

SM 2610957121 05-08 6/5/08 7:35 AM Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 3335-01 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info