Bedienungsanleitung Skil 3620 (Seite 12 von 136) (Alle Sprachen)

758599

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

! replace worn sanding sheets in time

! always use the tool with the total VELCRO surface

covered with sanding paper

• Dust suction w

! remove battery from tool

-use vacuum cleaner adapter J only when working with

sanding pad E

-mount vacuum cleaner adapter J as illustrated

-connect vacuum cleaner

! do not use dust extraction device/vacuum cleaner

when sanding metal

-clean vacuum cleaner adapter J regularly for optimal

dust pick-up performance

• On/o

-switch on/o the tool by pushing switch C 2 in “I”/”O”

position

! before the accessory reaches the workpiece, the

tool should run at full speed

! 

the workpiece

• Adjusting working speed e

-with wheel D the required oscillating frequency can

be adjusted from low (1) to high (6) (also while tool is

running)

-the optimal working speed depends on the material

and can be determined with practical trials

• Holding and guiding the tool

! while working, always hold the tool at the grey-

coloured grip area(s) r

-keep ventilation slots K uncovered

-do not apply too much pressure on the tool (excessive

pressure will cause excessive heat and may shorten

the service life of the accessory)

• Battery protection

Switches o the tool or prevents the tool from being

switched on, when

-the load is too high

-the battery temperature is not within the allowable

operating temperature range of -20 to +50°C

-the lithium-ion battery is nearly empty (to protect

against deep discharge)

! 



damaged

• LED-light L t

-LED-light L automatically lights on when activating

switch C

• Depth adjustment accessory (DEPTH STOP) (not

standard included) y

APPLICATION ADVICE

• For optimal results on dierent materials use table

u as reference for determining the right accessory

(accessories not standard included)

• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots K 2)

! remove battery from tool before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• When sanding metal, sparks are generated; do not use

vacuum cleaner and keep other persons and combustible

material from work area

BATTERIES

• The battery supplied is partially charged (to ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

-SKIL battery: BR1*31****

-SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

-when charging 4...40°C

-during operation –20...+50°C

-during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3 This tool accepts most commonly available multi-tool

accessories, including existing OIS and Starlock basic

accessories

4 Read the instruction manual before use

5 Batteries may explode when disposed of in re, so do not

burn battery for any reason

6 Store tool/charger/battery in locations where temperature

will not exceed 50°C

7 Do not dispose of electric tools and batteries together

with household waste material

USE

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Battery level indicator 8

-press the battery level indicator button M to show the

current battery level.

• Changing accessories q

! remove battery from tool

-remove/mount the required accessory as illustrated

-ensure that the openings of the accessory engage into

the tabs of the tool head (any snap-in position possible)

-mount the accessory with the depressed centre

pointing downwards

-loosen/fasten screw B with hex key A

-check the tight seating of the accessory (incorrect

or not securely fastened accessories can come loose

during operation and create a hazard)

• Mounting of sanding sheet 9

-tap the dust out of the VELCRO material on sanding

pad E before mounting the sanding sheet

-mount VELCRO sanding sheet H as illustrated

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 3620 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info