758395
10
Zoom out
Zoom in
Vorherige Seite
1/128
Nächste Seite
10
-empty dust bag regularly for optimal dust pick-up
performance
For using vacuum cleaner q
-mount vacuum cleaner adapter E as illustrated
-connect vacuum cleaner hose to vacuum cleaner
adapter E
On/o switch
-switch on/o the tool by pushing switch F 2 in/out
! before the sanding surface reaches the workpiece,
you should switch on the tool
! be aware of the sudden impact when the tool is
switched on
! 
the workpiece
Speed control w
For optimal sanding results on dierent materials
-with wheel G 2 you can set the desired sanding speed
-adjust speed to grit size used
-before starting a job, nd the optimal speed and grit by
testing out on spare material
Holding and guiding the tool r
! while working, always hold the tool at the grey-
coloured grip area(s)
-guide the tool parallel to the working surface
-do not apply too much pressure on the tool; let the
sanding surface do the work for you
-do not tilt the tool in order to avoid unwanted sanding
marks
-keep ventilation slots H 2 uncovered
Sanding
-the amount of material removed is determined by the
selection of the sanding sheet, the preselected sanding
speed and the applied pressure
! 
to an increase of the sanding capacity, but to
increased wear of the tool and the sanding sheet
! never use the same sanding sheet for wood and
metal
APPLICATION ADVICE
For determining the optimal grit (and speed), table e can
be used as reference
! 
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool and cord clean (especially ventilation
slots H 2)
-remove adhering sanding dust with a brush
-remove battery from tool before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
Permitted ambient temperature (tool/charger/battery):
-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Battery level indicator 7
-press the battery level indicator button J to show the
current battery level 7a
! when the lowest level of the battery indicator
7b, the
battery is empty
! 
after pressing button J 7c, the battery is not
within the allowable operating temperature range
Battery protection
The tool is suddenly being switched o or prevented from
being switched on, when
-the load is too high --> remove load and restart
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start ashing when
pressing button J 7c; wait until battery has returned
within the allowable operating temperature range
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level 7b is shown by the battery level indicator
when pressing button J; charge battery
! 

damaged
Backing pads
-never run the tool without backing pad A
! replace damaged backing pads immediately
(loosen/fasten 4 pad screws B)
! unplug tool before removing/mounting backing
pads
Mounting of sanding sheet 8
-mount VELCRO sanding sheet C as illustrated
-if necessary, clean backing pad rst
! perforation in sanding sheet should correspond
with perforation in sanding foot
! the dust suction requires the use of perforated
sanding sheets
! replace worn sanding sheets in time
Dust suction
! do not use dust box/dust bag/vacuum cleaner
when sanding metal
Dust bag 9
-mount dust bag D
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Skil 3745 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info