Bedienungsanleitung Skil 3900 (Seite 7 von 96) (Alle Sprachen)

644822

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools. Inspect tool cords and plugs

periodically and, if damaged, have them repaired by a

qualied person.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY INSTRUCTIONS FOR BENCH

GRINDERS

• This tool should not be used by people under the age of

16 years

• SKIL can assure awless functioning of the tool only

when the correct accessories are used which can be

obtained from your SKIL dealer

• Do not use damaged, deformed or vibrating

grinding wheels

• Use only grinding wheels with an allowable speed

matching at least the highest no-load speed of the

tool

• Before use, check that the grinding wheels are free of

damage, properly mounted, and able to rotate freely

• Replace the grinding wheel, if it is worn down to Ø

150 mm

• Always mount spark guard A 2 and tool rest C 2; never

use the tool without them

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Connect this earthed power tool only to a properly

earthed power supply system; ensure that socket

and extension cable have a functional protective

conductor

• Only use the anges which are supplied with this tool

• When grinding metal, sparks are generated; keep other

persons and combustible material from work area

• Keep hands away from the rotating grinding wheels

• Wear protective gloves 4 and use safety glasses 5

• The noise level when working can exceed 85 dB(A);

wear ear protection 6

• Anyone entering the work area must wear personal

protective equipment (fragments of the workpiece or of

a broken accessory may y away and cause injury

beyond the immediate area of operation)

• Never grind sidewards against the rotating grinding

wheel; only grind at the front

• Do not brake the grinding wheels with side pressure

• Allow the tool to cool down after a continuous use of

30 minutes (S

30 min.) 1

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Inspect the extension cord periodically and replace it,

if damaged

• Always disconnect plug from power source before

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of spark guard 7

- loosen screw B1 (do not remove it)

! regularly check the distance between spark

guard A and the grinding wheel (max. 2 mm) and

re-adjust, if necessary

- replace the grinding wheel, if it is worn down to the

point where spark guard A can no longer be adjusted

to the maximum distance of 2 mm

• Mounting of tool rest 8

! regularly check the distance between tool rest C

and the grinding wheel (max. 2 mm) and

re-adjust, if necessary

• Mounting tool on working surface 9

! for safe handling always mount tool on a flat and

stable working surface (e.g. workbench)

- use 4 mounting holes D for attaching the tool with

suitable screws to the working surface

- you may also clamp the tool to the working surface

with commercially available screw clamps

! remove 4 rubber supports E before mounting tool

on working surface

• On/o

Switch on/o the tool by pushing switch F 2 in “I”/”O” position

• Before using the tool for the rst time

- perform a sound-test on the grinding wheels (in

perfect condition they sound clear, when

tapped lightly)

- test-run the tool for at least 5 minutes without load

(stay out of danger area)

• Operating the tool 0

- lower spark guard A as far as possible

- switch on tool

- lay the workpiece to be ground on tool rest C

- move the workpiece lightly from the left to the right and

back (for optimal grinding results as well as uniform

wear of the grinding wheel)

- cool the workpiece in water from time to time

- switch o tool

Skil 3900 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info