Bedienungsanleitung Skil 4395 (Seite 7 von 40) (Englisch, Französisch, Spanisch)

758352

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Attaching the Blade

To prevent personal injury,

always disconnect plug from

power source before assembling parts, making

adjustments, or changing blades.

1. Insert the saw blade (teeth in cutting

direction) until it latches in the plunger (Fig. 2).

When inserting the saw blade, the back of the

blade must rest in the groove of the guide

roller (Fig. 3).

2. To remove blade, lift tool-less blade change

cover up with index finger and thumb and

remove blade.

For use with both T or U shank jigsaw blades.

-7-

Assembly

VARIABLE SPEED CONTROLLED

TRIGGER SWITCH

Your tool is equipped with a variable speed

trigger switch. The tool can be turned "ON" or

"OFF" by squeezing or releasing the trigger.

The speed can be adjusted from the minimum

to maximum nameplate SPM by the pressure

you apply to the trigger. Apply more pressure

to increase the speed and release pressure to

decrease speed (Fig. 1).

"LOCK-ON" BUTTON

The "Lock-ON" button, located in the handle of

your tool allows for continuous operation at

maximum SPM without holding the trigger (Fig. 1).

TO LOCK TRIGGER "ON": squeeze trigger,

depress button and release trigger.

TO UNLOCK THE TRIGGER: squeeze trigger

and release it without depressing the "Lock-

ON" button.

If the “Lock-ON” button is

continuously being depressed,

the trigger can not be released.

PLUNGER SPEED

The stroke rate may be adjusted as described

earlier under “Variable Speed Controlled

Trigger Switch”. The best results for a

particular application is determined by

experience, though as a general rule, slower

speeds are for denser materials and faster

speeds are for soft materials.

LASER LIGHT GUIDE (Model 4495 only)

The laser light guide is a class IIIA laser with a

maximum output power of 5.0m Watts and

conforms to 21 CFR 1040.10 and 1040.11.

LASER RADIATION. AVOID

DIRECT EYE EXPOSURE.

DO NOT stare into the laser light source.

Never aim light at another person or object

other than the workpiece. Laser light can

damage your eyes.

DO NOT use tinted glasses

to enhance the laser light.

Tinted glasses will reduce overall vision for

the application and interfere with the normal

operation of the tool.

Never aim the beam at a

workpiece with a reflective

surface. Bright shiny reflective sheet steel or

similar reflective surfaces are not

recommended for laser use. Reflective

surfaces could direct the beam back toward

the operator.

Use of controls or adjustments

or performance of procedures

other than those specified herein may result in

hazardous radiation exposure.

The use of optical instruments

with this product will increase

eye hazards.

WARNING

Operating Instructions

FIG. 2 FIG. 3

TOOL-LESS

BLADE CHANGE

COVER

ROLLER

GUIDE

BLADE

DANGER

WARNING

CAUTION

SM 1619X03034 07-08 7/2/08 1:38 PM Page 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 4395 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info